Bedienungsanleitung Power Dynamics PDA 12 (Seite 5 von 12) (Deutsch, Englisch, Holländisch, Spanisch)

506156

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

5 - 12

IMPORTANT

A cable that is too light will result in amplifier power being wasted due to the series resistance of the cable.

In addition, loss of low-frequency performance may be experienced due to a degraded damping factor.

Keep in mind that two 8 Ohm parallel linked speakers will equal a 4 Ohm load.

Looping speakers

Running too many speakers from a single amplifier channel may result in damage to the amplifier and/or in

degraded audio performance. To calculate the combined impedance of multiple identical speakers in

parallel, please use the formula below:

Impedance of a single speaker

--------------------------------------------------------- = Amplifier load

Number of speakers connected in parallel

Refer to your power amplifiers owners manual, for information on minimum recommended load impedance.

TROUBLESHOOTING

One certain method of determining if a speaker is faulty is to substitute a speaker that is known to work

correctly for the suspected problem speaker. If the “normally correct speaker” is experiencing the same

difficulties or problems as the suspected problem speaker, use the information below to isolate the problem.

No output

Possible cause / Action:

Speaker cables; reseat all connectors, substitute known good speaker cables, check solder joins, tighten

set-screws, inspect cable for damage, inspect wire or connector for stray strand that may short

Amplifier; make sure the amplifier channel is being fed a signal, most amps have a “signal input” LED to

indicate the presence of a signal, re-patch the speaker to an amplifier channel that is known to work.

Intermittent

Possible cause / Action:

Poor connections While it is possible for a faulty speaker to exhibit intermittent output, it’s more likely

that an output cable/connector is the problem. Check the soldering on your connectors. Tighten the set-

screws.

Constant noise, buzzing and/or humming

Possible cause / Action:

Faulty electronic; Any constant noise originates in the amplifier, mixer, signal processing, source device in

the signal devices, or line-level wiring. Check and correct system grounding as required. Chain check for

noisy sources or electronic components. Check wiring for shielding.

Poor low-frequency output

Possible cause / Action:

Improper polarity: When two speakers in close proximity to each other are connected out-of-polarity, they

can partially cancel each other out, especially at low frequencies. Check your speaker cables to be sure they

are all identically wired and connected. Check the balanced line signal cables to be sure they are all

correctly wired.

Do not attempt to make any repairs yourself. This would invalid your warranty. Do not make any changes to the unit.

This would also invalid your warranty. The warranty is not applicable in case of accidents or damages caused by

inappropriate use or disrespect of the warnings contained in this manual. Tronios cannot be held responsible for

personal injuries caused by a disrespect of the safety recommendations and warnings. This is also applicable to all

damages in whatever form.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Power Dynamics PDA 12 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info