Bedienungsanleitung Power Plate Pro 7 (Seite 9 von 14) (Englisch)

703787

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

Guidance and manufacture’s declaration – electromagnetic emissions-

for all ME EQUIPMENT and ME SYSTEMS

Guidance and manufacture’s declaration – electromagnetic emission

The Pro7 is intended for use in the electromagnetic environment specied below. The customer of the user

of the Pro7 should assure that it is used in such an environment.

Emission test Compliance Electromagnetic environment – guidance

Group 1 The Pro7 use RF energy only for its internal function.

Therefore, its RF emissions are very low and are not

likely to cause any interfe rence in nearby electronic

equipment.

RF emission CISPR 11 Class B Class A with IEC61000-3-2

Complies with IEC61000-3-3

Harmonic emissions Class A The Pro7 is suitable for use in all establishments,

IEC 61000-3-2 including domestic establishments and those directly

connected to the public low-voltage power supply

Voltage uctuations/ Comply network that supplies buildings used for domestic

icker emissions purposes.

IEC 61000-3-3

Wi-Fi Specications Network Standard: IEEE 802.11b/g/n

Band: 2.400-2.4835GHz

Cover Range: 20meter

Wi-Fi Power: 10dBm

Guidance and manufacture’s declaration – electromagnetic immunity –

for all ME EQUIPMENT and ME SYSTEMS

Guidance and manufacture’s declaration – electromagnetic immunity

The Pro7 is intended for use in the electromagnetic environment specied below. The customer or the user of

Pro7 should assure that it is used in such an environment.

Immunity test IEC 60601 test level Compliance level Electromagnetic environment - guidance

Electrostatic ±6 kV contact ±6 kV contact Floors should be wood, concrete or

discharge (ESD) ±8 kV air ±8 kV air ceramic tile. If oor are covered with

IEC 61000-4-2 synthetic material, the relative humidity

should be at least 30%.

Electrical fast ±2 kV for power ±2kV for power Mains power quality should be that of

transient/burst supply lines supply lines a typical commercial or hospital IEC

61000-4-4 environment.

Surge ± 1 kV line(s) t ±1 kV differential Mains power quality should be that of

IEC 61000-4-5 o line(s) mode a typical commercial or hospital

environment.

Voltage dips, short <5% U

<5% U

Mains power quality should be that

interruptions and (>95% dip in U

) (>95% dip in U

) of a typical commercial or hospital

voltage variations for 0.5 cycle for 0.5 cycle environment. If the user of the Pro7

on power supply requires continued operation during

input lines 40% U

40% U

power mains interruptions, it is IEC

61000-4-11 (60% dip in U

) (60% dip in U

) recommended that the Pro7 be powered

for 5 cycles for 5 cycles from an uninterruptible power supply or a

bat ter y.

70% U

(30% dip in U

) (30% dip in U

)

for 25 cycles for 25 cycles

<5% U

(>95% dip in U

) (>95% dip in U

)

for 5 sec for 5 sec

Power frequency

3A/m

Power frequency magnetic elds should

(50Hz) magnetic be at levels characteristic of a typical

61000-4-8

location in a typical commercial or

hospital environment.

NOTE U

is the a.c. mains voltage prior to application of the test level.

EMC Declaration

of 22 15 of 22

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Power Plate Pro 7 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info