Bedienungsanleitung Powerpeak Slim Line FET8315P manueel (Seite 26 von 72) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

613976

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Longwoods Ltd._04_2013

TIME

Press the ENTER-key until TIME function appears on the display. Next, press the UP- or DOWN-key

to set the time. Time is adjustable from 1:00 – 99:00 minutes. The computer counts down from the

set value to 00:00. An audio signal sounds once the set value has been reached. If you do not preset

any time, the computer will display the current training time from 00:00 – 99:59 minutes.

SPEED

The computer displays the current speed from 0.0 – 99.9 km per hour.

RPM

The computer displays the current revolutions per minute from 15 – 999 revolutions.

DISTANCE

Press the ENTER-key until DIST. (distance) function appears on the display. Next, press the UP- or

DOWN-key to set the distance. The distance can be set from 1.0 – 999.0 km. The computer counts

down from the set value to ‘0.0’. An audio signal will sound once the set value has been reached.

If you do not preset any distance, the computer will display the current covered distance from 0.1 –

999.9 km.

CALORIES

Press the ENTER-key until CAL. (calories) function appears on the display. Next, press the UP- or

DOWN-key to set the calories to be burned. The number of calories to be burned can be set from 1.0

– 999.0 calories. The computer counts down starting from the set value to ‘0.0’. An audio signal will

sound once the set value has been reached. If you do not preset the number of calories to burn, the

computer will display the current burned calories from 0.1 – 999.0 calories.

T.H.R.

Press the ENTER-key until T.H.R. function appears on the display. Next, press the UP- or DOWN-key

to set the number of heartbeats per minute. The number of heartbeats per minute can be set from

60-220 pulses. Place your palms on the hand pulse sensors on the handlebar. The display shows

you the current number of beats per minute. An audio signal will sound once the set value has been

reached.

Attention: if during 15-20 seconds no signal is being transmitted from the hand sensors, a ‘P’ will

appear on the display. This means that the computer is in energy saving mode. Press any key to

resume the T.H.R. measurement.

RECOVERY

Press on RECOVERY-key if you wish to measure your condition after the training. Place your palms

for 1 minute on the hand pulse sensors on the handlebar. The display shows the condition in a figure

ranging from 1.0 to 6.0, where 1.0 indicates a good condition and 6.0 a bad condition.

IMPORTANT ADVICE FOR TRAINING

• Before you start the training, consult your doctor. Ask what kind of training is suitable for you.

Wrong or excessive training can cause health defects.

• Avoid over exercising. Do not train if you are tired or feeling faint. If you are not used to physical

activity, start the training slowly at the beginning.

• Stop exercising immediately if you feel pain or any other troubles.

• Pay attention to your breathing during training.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerpeak Slim Line FET8315P manueel Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info