Bedienungsanleitung Powerplus pow xq 5203 (Seite 7 von 11) (Englisch)

389288

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

POWXQ5203 EN

 The switch should be in 'drill’ position when drilling holes in tiles.

*(1)selector switch (4) set for Hammer mode. / (2) selector switch (4) set for drilling mode.

8.5 Reversible action (left / right) (fig 6)

The direction of rotation on your drill can be reversed.

 The direction of rotation is controlled by a lever (6) located above the on/off switch (9).

 With your drill held in normal operation position the direction of rotation-lever (6) should be

positioned to the right of the trigger for forward drilling operation.

 The direction of rotation is in reverse (left), when the lever is turned to the left of the on/off

switch.

Don’t change the direction of rotation while your drill is still turning.

8.6 Insert a drill / bit. (fig 7)

 To open the keyless chuck, hold the rear ring, turn the front ring anti-clockwise. When

jaws are open sufficiently, insert the drill / bit and re-close the chuck turning the front ring

clockwise, tighten it securely.

 To unlock, turn clockwise again)

9 USE

 Use only correctly sharpened drill bits which are suitable for the material being drilled.

 When drilling hard materials, firm pressure is required on the power tool. However,

excessive pressure does not improve performance and places unnecessary pressure on

the tool and its bit.

 Always apply pressure in straight line with the drill whiling drilling. Use enough pressure to

keep the drill biting but do not push too hard to avoid stalling the motor or damaging the

drill.

 Warning! If the drill stalls, release the trigger switch immediately and remove the drill from

the work to determine the cause of stalling.

 Use the auxiliary handle where possible to gain extra control and to prevent fatigue.

Use auxiliary handle supplied with the tool. Loss of control can cause

personal injury!

 To minimize the chance of sudden stalling and breaking through the material, reduce the

pressure on the drill and ease the drill .

 Keep the motor running when pulling the drill back out of a drilled hole. This will help

prevent jamming.

9.1 Drilling in Metal

 For maximum performance, use high speed steel bits for metal or steel drilling.

 Turn drilling mode selector to drilling mode.

 Use a center punch to mark the hole location on the workpiece.

 Begin drilling at a very low speed to prevent the drill from slipping off the starting point.

 Maintain a speed and pressure which allows cutting without overheating the bit. Applying

too much pressure will: overheat the drill, wear the bearing, bend or burn bits, produce off-

center or irregular shaped holes.

 When drilling large holes in metal it is recommended to drill with a small drill at first, then

finish with a larger drill, also, lubricate the drill with oil to improve drilling action and

increase drill life.

9.2 Drilling in Wood

 For maximum performance, use high speed steel bits for wood drilling.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus pow xq 5203 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus pow xq 5203

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info