Bedienungsanleitung Powerplus POW30620 (Seite 5 von 8) (Englisch)

582133

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

POW30620 EN

 Do not burn the battery.

 Never attempt to open the battery.

 In case of skin contact of the battery fluid (a solution of 25-30% potassium hydroxide),

flush immediately with abundant water. Neutralize with a mild acid such as lemon juice or

vinegar. In case of eye contact, rinse abundantly for 10 minutes with clean water and

consult a physician.

8 OPERATION

8.1 Charging the battery (Fig. B)

The battery (6) must be charged before first use. Only after several charge and discharge

cycles the battery will attain full capacity.

 Remove the battery from the machine.

 Connect the battery to the charger.

 Insert the mains adaptor of the charger into a mains outlet. Red LED lights. The green

charging indicator lights when the battery is charging. Never charge the battery for more

than 5 hours. If the battery is fully charged, the green charging indicator will remain lit.

8.2 Positioning and removing a drill or screw bit

This tool is equipped with a keyless chuck.

 Open the chuck by turning the collar.

 Insert the drill or screw bit in the chuck.

 Close the chuck by firmly tightening the collar while holding the rear part of the chuck with

the other hand.

 In order to remove the drill or screw bit proceed in reverse order. Before positioning or

removing a drill or screw bit always remove the battery from the machine.

8.3 Forward/reverse switch (Fig. A)

 Push the forward/reverse switch (2) from right to left side to drill holes and fasten screws.

 Push the forward/reverse switch (2) from left to right side to loosen screws. Always wait

until the motor has come to a complete standstill before changing the direction of rotation.

8.4 Adjusting the torque (Fig. C)

This machine has been fitted with an adjustable coupling (20+1 pos) to limit the torque when

tightening screws.

 Turn the adjustment collar (3) clockwise to reduce the torque and counterclockwise to

increase the torque. The correct setting depends on the type and size of the screw and the

work piece.

 In case of doubt, start with the lowest setting and increase the torque until you have

reached the desired result.

 For drilling, turn the adjustment collar fully counterclockwise (to the drilling symbol).

8.5 Switching on and off (Fig. A)

 To switch on the machine, press the on/off switch (1).

 To switch off the machine, release the on/off switch.

9 CLEANING AND MAINTENANCE

Attention! Before performing any work on the equipment, pull the power

plug.

9.1 Cleaning

 Keep the ventilation slots of the machine clean to prevent overheating of the engine.

 Regularly clean the machine housing with a soft cloth, preferably after each use.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POW30620 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POW30620

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info