Bedienungsanleitung Powerplus POW4110 (Seite 5 von 8) (Englisch)

582164

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

POW4110 EN

 Use safety glasses, especially when you sand above your head.

 Do not bring pressure to your machine, this will only delay the sanding.

IMMEDIATELY SWITCH OFF THE MACHINE WHEN:

 Excessive sparking of the carbon brushes and a ring of sparks in the collector.

 Interruption of the mains plug, mains lead or mains lead damage.

 Defect switch

 Smoke or stench of scorched isolation

7 OPERATION

7.1 Choice of the sand-paper

Coarse sandpaper (grain 50) removes in general the bigger part of the material and fine sand-

paper is used for the finishing. If the surface is not even, then start with rough sandpaper.

Further you use middle coarse sandpaper(grain 80) to remove the scratches left behind by the

coarse sand-paper and finally you take fine sandpaper (grain 120) for the finishing.

7.2 Removing and installing the sanding belt

Before assembly the sanding belt always remove the plug from the mains.

 Put the machine on its side, with the drive belt cover (10. Fig. A) down wards.

 Loosen the sanding belt fastener (7, Fig A).

 Remove the sanding belt from the machine.

 Put a new sanding belt on the machine, make sure that the direction arrows on the

sanding belt are pointing in the same direction as the direction indicator.

 Fasten the sanding belt fastener again (7. Fig. A).

7.3 Aligning the sanding belt

If the sanding belt doesn't run parallel with the outer edge of the housing, the sanding belt

must be aligned. Move the sanding belt in the correct position with the adjusting knob (6. Fig.

A). By turning the adjusting knob clockwise the sanding belt will move to the inside and by

turning anti-clockwise the sanding belt will move to the outside.

7.4 Switching on and off

 To switch the machine on press the on/off switch (I. Fig. A).

 To switch the machine off release the on/off switch (I. Fig.A).

It continuous operation is required the blocking switch (4 fig. A) must be used:

 Switch the machine on to press the on/off switch.

 Press the blocking switch (4. Fig. A) and release the on/off switch.

 To switch the machine off press the on/off switch again and release the on/off switch.

7.5 Mounting dust bag

Use the dust bag to collect dust which is released during sanding.

 Put the dust bag on the dust collection opening (5. Fig. A).

 Empty the dust bag regularly in order to obtain an efficient dust extraction.

7.6 Grip

The use of the belt sander is made easier because of the two grips one on the front side and

one on the back. Through that you can hold the machine with two hand*, you have a better

control of the machine and there is less risk to becoming in touch with the moving parts. Hold

the belt sander always with both hands.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POW4110 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POW4110

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info