Bedienungsanleitung Powerplus POW5100 (Seite 5 von 7) (Englisch)

582171

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

POW5100 EN

 It is compulsory to wear certified gloves and protective goggles when using the device.

 Never use the machine without its protective guard and “spark guards”.

 Always check that the work supports are firmly fixed before using the machine.

 As the wheel wears down, adjust the work support and screen slide:

 1.5mm between the work support and the wheel

 2mm between the slide and the wheel

 When using the grinder, stand in a stable, balanced position, without stretching, and keep

children at a distance.

 Never leave the machine running unsupervised. Keep the workshop clean and tidy.

 Before use, make sure the grinding wheels are not damaged or cracked. If there is the

slightest doubt, replace at once (a damaged grinding wheel can fly apart at speed).

 Replacement grinding wheels must be identical in characteristics and dimensions.

 This machine is not suitable for grinding soft substances such as lead, magnesium or light

alloys.

7 ASSEMBLY

ATTENTION! Disconnect the power plug before carrying out any

adjustments or maintenance.

 Fit the work supports (10) using the bolts supplied. Set these work supports not more than

2mm from the grinding wheel.

 Fit the transparent protection screens (6), (7) using the screws supplied, over the wheel

guards. The clearance between the slide (7) and the wheel must not exceed 2mm.

Whenever the machine is used, the screen must be in low position.

 It is strongly recommended that the grinder should be bolted to a bench or work table. The

length of the bolts will be determined by the thickness off the bench top. The machine

must be fixed by 4 bolts in the places provided for them in the base (1). The grinder is

fitted with rubber “anti-vibration” shoes. Nevertheless, the inclusion of a piece of soft wood

between the base and the bench is recommended for better absorption of vibrations.

8 OPERATION

 This machine is designed for sharpening tools or grinding small parts. It is not suitable for

grinding heavy sheet metal parts.

 Use the appropriate grinding wheel for the job: the “SOFT” wheel for hard metals / the

“HARD” wheel for soft metals.

 Do not grind wood, plastic, soft alloys (e.g. lead) or similar materials, as this would clog

the grinding wheels.

 Apply gradually increasing pressure to the part to be ground, which must not be brought

into sudden contact with the grinding wheel.

 For prolonged grinding operations, cool the work at regular intervals in water. Some tools

(e.g. wood chisels) must not be ground “blue”.

 Hold the work-piece firmly so that it cannot jam between the grinding wheel and the

support (with risk of damage or even fracture of the wheel).

 Changing the grinding wheel (tools required: wrench 19mm – wrench 8mm – cross-head

screwdriver): Machine disconnected

 remove the spark-guard (6) or (7) and wheel guard (5) or (9),

 unscrew wheel fixing nut

Warning: seen from in front, the shaft on the right has a right-hand

(conventional) thread, and the shaft on the left a left-hand thread.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POW5100 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POW5100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info