Bedienungsanleitung Powerplus POW726 (Seite 3 von 6) (Englisch)

645233

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

POW726 EN

 Always fasten the nut tightly when attaching the tip. This ensures a good electric

connection. Ventilate the place of work sufficiently in order to take unwanted vapors

quickly away from melting material.

 The mains power supply lead for the soldering gun may only be replaced by a

specialist electrician.

 Use only original accessories which are supplied or recommended by the

manufacturer.

 This appliance can be used by children aged from 8 years and above and persons

with reduced physical, sensory or mental capabilities or lack of experience and

knowledge if they have been given supervision or instruction concerning use of the

appliance in a safe way and understand the hazards involved.

 Children shall not play with the appliance.

 Cleaning and user maintenance shall not be made by children without supervision

5 OPERATION

5.1 Connection

This soldering gun may only be connected to single phase alternating current. The voltage

of the electric power supply on the network must correspond with the instructions on the

type plate of the machine. Connection to a socket without an earthed contact is also

possible since the double insulation complies with the standard requirements according to

DIN EN60335-1:2002.

5.2 Switching on

CAUTION’ Use this appliance only for work which is included in the

established operative range

 Switch-on: press switch 4 and Leave: approx.l000g pressed. Status indicator 3

lights up when the appliance is switched on.

 Switch-off: release switch 4.

 The duration of the current supply determines the heat of the solder (longer current

supply = higher solder temperature). While soldering, do not keep the switch pressed

for too long. Determine the necessary duration for current supply in practice through

control of the temperature of the solder. In order to achieve a constant temperature,

avoid constant current for more than 12 seconds and cutoff current of over48

seconds. As soon as you release the switch, the temperature of the solder is

automatically reduced. A subsequent turning on of the switch ensures a fast increase

in temperature. Constant solder temperature guarantees optimum solder quality,

avoids running the soldering tip at temperatures which are too high and extends the

service life of the appliance.

Below, we give you some examples of poorly soldered joints:

 It the soldering tin is tear-shaped, the soldering coagulate was too cold.

 If the soldering tin is dull and slightly porous or crystalline, the parts were probably

moved during the cooling process.

 If too little soldering tin has been left in the joint, the soldering was too warm or the

soldering tin was not melted sufficiently.

 If the soldering tin is yellow or black, this means that too much soldering paste has

been used or that the inner core of the tin solder wire has become overheated during

soldering.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POW726 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POW726

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info