Bedienungsanleitung Powerplus POWAIR0021 (Seite 3 von 8) (Englisch)

795365

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

POWAIR0021 EN

 WARNING! Check correct air pressure is maintained and not exceeded. We

recommend 90psi.

 Keep air hose away from heat, oil and sharp edges. Check air hose for wear before

each use and ensure that all connections are secure.

 Only use impact sockets/Chisels /Grinding Stones which are specifically designed for

use with an impact wrench./Ratchet Wrench /Air Hammer.

 WARNING Inspect Sockets/Grinding Stones/Chisels daily for excessive wear or

cracks.

 Caution! Impact wrench /Ratchet wrench sockets and accessories must be used with

this tool. Do not use hand sockets and accessories.

 Caution! The spring retainer holds chisel in place, it must be secure before the chisel

can operate properly.

 Caution! Die grinder accessories rated for 10,000 RPM or more

 Wear approved safety eye/face shield, ear defenders, and hand protection.

 WARNING! Due to the possible presence of asbestos dust from brake linings, when

working around vehicle brake systems we recommend you wear suitable respiratory

protection.

 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-

slip shoes.

 Keep children and non essential persons away from the working area.

 DO NOT use the wrench for a task it is not designed to perform.

 DO NOT use wrench if damaged or thought to be faulty.

 DO NOT use wrench unless you have been instructed in its use by a qualified

person.

 DO NOT carry the wrench by the air hose at yourself or others.

 DO NOT direct air from the air hose at yourself or others.

 When not in use disconnect from air supply and store in a safe, dry, childproof

location.

4 AIR SUPPLY

 Ensure air valve (or trigger) is in the “off” position before connecting to the air supply.

 You will require an air pressure of 90psi, and an air flow according to specification.

 WARNING! Ensure the air supply is clean and does not exceed 90psi while operating

the tool. Too high an air pressure and unclean air will shorten the product life due to

excessive wear, and may be dangerous causing damage or personal injury.

 Drain the air tank daily. Water in the air line will damage the tool.

 Clean air inlet filter weekly.

 Line pressure should be increased to compensate for unusually long air hoses (over

8 meters). The minimum hose diameter should be 3/8” I.D. and fittings must have the

same inside dimensions.

 Keep hose away from heat, oil and sharp edges. Check hose for wear, and make

certain that all connections are secure.

5 LUBRICATION

An automatic in-line filter-regulator-lubricator is recommended (Fig. 1) as it increases tool

life and keeps the tool in sustained operation. The in-line lubricator should be regularly

checked and filled with air tool oil.

Proper adjustment of the in-line lubricator is performed by placing a sheet of paper next to

the exhaust ports and holding the throttle open approximately 30 seconds. The lubricator

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWAIR0021 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWAIR0021

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info