Bedienungsanleitung Powerplus POWAIR0310 (Seite 3 von 8) (Englisch)

582112

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

POWAIR0310 EN

 Repairs can only be effected by official dealers.

 To prevent injuries to yourself and bystanders, refer to tool use, maintenance and

troubleshooting sections for additional information (fig. 1).

 To prevent eye injuries, always wear safety glasses with hard plastic side shields.

Be sure everyone in your work area is wearing the same type of safety glasses (fig.

2).

 Always wear hearing protection and a hard hat (fig. 3).

 Never use hydrogen, oxygen, carbon dioxide or any other bottled gas as a power

source for this tool, the tool will explode and cause serious injury (fig. 4).

 Remove your finger from trigger when not driving fasteners. Never carry the tool with

finger on the trigger, the tool will eject a fastener when the safety is pressed (fig. 5).

 Never connect the tool to an air hose with pressure exceeding 200 psi or 13.7 bar

(fig. 6).

 Air compressors must comply with requirement ANSI B19.3 1981 (U.S.), "Safety

Standard for Compressors for Process Industries" (fig. 7).

 Air hose minimum working pressure rating of 150 psi (10.3 bar) or 150% of the

maximum pressure produced in the system is absolutely necessary (fig. 8).

 The tool and air supply hose must have a hose coupling such that all pressure is

removed from the tool when the coupling joint is disconnected (fig. 9).

 Use only compressed air coming through 3 pieces set (fig. 10).

 Never load the tool if it is connected to air supply (fig. 11).

 Never use the tool if the safety element, trigger or springs have become inoperative,

missing or damaged. It is hazardous to remove the safety element, trigger or spring

(fig. 12).

 Before using this tool, make sure trigger, screw and cap are securely tightened (fig.

13).

 Do not modify tool without authorization (fig. 14).

 Disconnect the tool from the air supply whenever the tool stops working (fig.15).

 Keep the tool pointed away from yourself and others (fig. 16).

 Fire fasteners into work surface only, never into materials too hard to penetrate (fig.

17).

 Do not drive fasteners on top of other fasteners. Firing the tool in an inclined angle is

also forbidden (fig. 18).

 Do not push safety element on work surface until a second fastener is desired (fig.

19).

 Do not drive fasteners close to the edge of the work surface. The work piece is likely

to split and the fastener could fly free and hit someone (fig. 20).

 Do not load fasteners with trigger or safety element depressed (fig. 21).

 Do not use tool without Danger-label on tool (fig. 22).

 Never use a tool that leaks air or needs repair (fig. 23).

 Be sure you are in a balanced position when using or handling the tool (fig. 24).

 Operate the tool at recommended pressure of 4-8 bar.

5 ADDITIONAL INSTRUCTIONS FOR FASTENER DRIVING TOOLS OPERATED BY

COMPRESSED AIR

 fastener driving tools operated by compressed air shall only be connected to

compressed air lines where the maximum allowable pressure cannot be exceeded

by a factor of more than 10%, which can for example be achieved by a pressure

reduction valve which includes a downstream safety valve;

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWAIR0310 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWAIR0310

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info