Bedienungsanleitung Powerplus POWAIR0805 (Seite 5 von 10) (Englisch)

676276

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

POWAIR0805 EN

 It must be checked that the maximum operating speed of the machine tool is higher

than the nominal speed of the machine.

 It must be checked that the hook&loop abrasive sheets can be affixed concentrically

to the mounting plate.

4.7 Hazards in the work environment

 Slipping, tripping and falling are the main causes of injuries at the workplace. Keep in

mind that surfaces may have become slippery during machine use, and remember

tripping hazards caused by the air or hydraulic hose.

 Proceed with caution in unfamiliar surroundings. There may be hidden dangers due

to electrical cables or other supply lines.

 This machine for grinding and sawing is not suitable for use in explosive

environments and is not insulated against contact with electrical power sources.

Therefore, it may not come into contact with electrical power sources!

 Verify that there are no electrical lines, gas lines, etc. that may result in a hazard in

the event of them becoming damaged during machine use.

5 ADDITIONAL SAFETY INSTRUCTIONS FOR PNEUMATIC MACHINERY

 Compressed air can result in serious injuries.

 Always close the air supply, release pressure from the hose, and disconnect the

machine from the compressed air supply, when the machine is not in use, before

switching accessories or when performing repairs.

 Never aim the air flow at yourself or others.

 Hoses flapping about can result in serious injuries. Therefore always inspect hoses

and their fasteners for damage and a secure fit.

 If using universal swivel couplings (coupling discs) always use locking pins and use

whip-check hose safety cables for protection in the event the connection between the

hose and the machine or in between hoses fails.

 Ensure not to exceed the maximum pressure specified on the machine.

 Never carry pneumatic tools by the hose.

6 AIR SUPPLY

 Ensure air valve (or trigger) is in the “off” position before connecting to the air supply.

 Item will require air pressure of 90psi, and air flow according to specification.

 Drain the air tank daily.

 Clean air inlet filter weekly.

 Line pressure should be increased to compensate for unusually long air hoses (over

8 meters). The hose diameter should be 3/8” I.D.

 Keep hose away from heat, oil and sharp edges. Check hose for wear, and make

certain that all connections are secure.

7 LUBRICATION

An automatic in-line filter-regulator-lubricator is recommended (Fig 1) as it increases tool

life and keeps the tool in sustained operation. The in-line lubricator should be regularly

checked and filled with air tool oil.

Proper adjustment of the in-line lubricator is performed by placing a sheet of paper next to

the exhaust ports and holding the throttle open approximately 30 seconds. The lubricator

is properly set when a light stain of oil collects on the paper. Excessive amounts of oil

should be avoided.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWAIR0805 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWAIR0805

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info