Bedienungsanleitung Powerplus POWC1060 (Seite 6 von 10) (Englisch)

644863

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

POWC1060 EN

 During the charge process, the current used should correspond to the current of the

battery charger.

 Never let moisture, rain or splashed water reaches the charging location.

 The ambient temperature must not exceed 40oC. Never expose the device to direct

insulation.

 Storage-battery packet, which are defective or damaged or can no longer be recharged,

must be disposed of as hazardous waste. Hand them over at a special collection point.

Never harm our environment. Do not throw unusable storage-battery packet away into the

domestic waste, into fire or into water.

 If the electrical cable is damaged, the wire may only be replaced by the supplier or by his

repair workshop. Have repairs carried out only by an authorized specialist only.

 Use only storage-battery packet, which have been produced by the original manufacturer.

 Always keep the surface of the charger free from dust and dirt.

 Insert the battery packet into the charger. Follow the guidelines provided concerning

polarity.

 Always remove battery packet before working on the machine

 When the battery packet is outside the drill, cover the contacts to avoid short circuits (e.g.

from tools)

 Do not throw batteries into water or fire, risk of explosion!

 Protect the battery packet from impacts, and don't open it.

 Never discharge the battery packet completely and recharge occasionally if not used for a

prolonged period.

7.2 Residual risks

Even when the tool is used as prescribed it is not possible to eliminate all residual risk factors.

The following hazards may arise in connection with the tool’s construction and design:

 Damage to lungs if an effective dust mask is not worn.

 Damage to hearing if effective hearing protection is not worn.

 Health defects resulting from vibration emission if the power tool is being used over longer

period of time or not adequately managed and properly maintained.

WARNING! This machine produces an electromagnetic field during

operation. This field may under some circumstances interfere with active or

passive medical implants. To reduce the risk of serious or fatal injury, we

recommend persons with medical implants to consult their physician and

the medical implant manufacturer before operating this machine.

8 OPERATION

8.1 Charging the battery (fig. 1)

The battery (5) must be charged before first use. Only after several charge and discharge

cycles the battery will attain full capacity.

 Remove the battery from the machine. (a)

 Connect the battery to the charger. (b)

 When the red indicator light starts winking, this means the battery pack is now being

charged. Normally it will take 3-5 hour to fully charge the battery. When the red indicator

light stops winking and the green light starts winking, this means the battery is fully

charged

 Avoid short periods of charging. Only charge battery pack when fully empty.

 Adaptor, charger and battery pack will be warm when charging. This is normal.

8.2 Positioning and removing a drill or screw bit (fig. 2)

This tool is equipped with a keyless chuck.

 Open the chuck by turning the collar.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWC1060 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWC1060

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info