676319
5
Zoom out
Zoom in
Vorherige Seite
1/8
Nächste Seite
POWC2060 EN
Copyright © 2017 VARO P a g e | 5 www.varo.com
When removing the saw blade (8), follow the above procedure in reverse order.
Before plugging in power cord, always pull on the blade (8) to make sure it
is securely locked in the clamp. Failure to do so may result in serious
injury.
8 OPERATION
8.1 Switch on/off (3)
Connect the plug to the power supply.
Turn on or turn off the tool by squeezing or releasing the ON/OFF switch trigger (3).
For continuous operation just press the lock-on button (4) on the left side of the handle.
The lock-on button can be release by pressing the switch trigger again.
8.2 To change position of the pivot shoe assembly (Fig 2)
Unplug your saw.
WARNING: Failure to unplug your saw could result in accidental starting
causing serious injury.
Loosen the both cap screws (6) in the gear frame with hex key.
Reposition pivot shoe (1) assembly in or out.
Retighten both cap screws (6) securely. Do not over tighten cap screws (8).
Remove hex key.
WARNING: Cutting into electrical wiring in walls can cause blade, blade
clamp, and saw bar assembly to become electrically live. Do not touch
metal parts when cutting into a wall; grasp only the insulated gripping
surfaces provided by the tool. Make sure hidden electrical wiring, water
pipes, and mechanical hazards are not in the blade path when cutting into a
wall.
8.3 General cutting
Clamp your work piece if it is portable. Rest the front shoe of the saw on your work piece (be
sure the blade is not contacting the work piece) and start the saw, exerting enough pressure in
the direction of the cut to keep the shoe pressed firmly against the work piece at all times. Do
not force the cut or stall the saw. Don’t bend or twist the blade, let the tool and the blade do
the work. In general, coarser blades are for wood, plastics, and composites, and finer blades
are for cutting metal. Chattering or vibration may indicate you need a finer blade or higher
speed. If the blade overheats or clogs, it may indicate you need a coarser blade. Replace
blades when they become dull. Dull blades will produce poor results and may overheat the
saw.
8.4 Plunge cutting
Clearly mark the line of cut, from a convenient starting point within the cut out area. Place the
tip of the blade over that point with saw parallel to the line of cut, slowing lower the saw until
the bottom edge of the shoe rests on the work piece and the blade not touching the work piece.
Start the saw and allow it to attain full speed. With the saw resting on the shoe, slowly tilt the
saw forward to lower the blade onto the cut line. Continue this motion until the saw blade is
perpendicular to the work piece.
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Powerplus POWC2060 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Powerplus POWC2060

Powerplus POWC2060 Bedienungsanleitung - Deutsch - 10 seiten

Powerplus POWC2060 Bedienungsanleitung - Holländisch - 9 seiten

Powerplus POWC2060 Bedienungsanleitung - Französisch - 9 seiten

Powerplus POWC2060 Zusatzinformation - Alle Sprachen - 2 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info