Bedienungsanleitung Powerplus POWDP1510 (Seite 7 von 13) (Englisch)

675938

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

POWDP1510 EN

 No memory effect (capacity loss after several charge/discharge cycles) like other type

batteries. (Ni-Cd, Ni-MeH ..).

 Limited self discharge. (also see chapter : Storage)

8.2 Keyless chuck (1)

Your drill has a keyless chuck that allows you to hand tighten or release drill bit in the chuck

jaws.

8.3 Torque adjustment ring (2)

The drill has a torque adjustment ring. It allows you to select the desired torque depending on

the task you have to perform (drill / different types of screws into different materials). The

proper setting depends on the type of material and the size of screw you are using.

8.4 Forward/reverse selector (right/left rotation selector) (6)

The drill has a forward/reverse selector located above the switch trigger.

CAUTION: To prevent damage to the gearbox, always allow the chuck to come to a complete

stop before changing the direction of rotation or selecting another speed (HI-LO). To stop,

release the trigger switch.

8.5 Variable speed

Your cordless drill has a variable speed switch. The rotational speed and torque will in-/

decrease equivalently to applied trigger pressure. This drill has an electric brake, when the

trigger switch is released, the chuck stops turning.

8.6 Speed selector (3)

Your cordless drill has a two-speed gear, designed for drilling or driving at LO (1) or HI (2)

speed. A slide switch is located on top of your drill to select either LO (1) or HI (2) speed.

8.7 LED light (7)

Your cordless drill is equipped with an LED light at the front, above the battery pack

8.8 TPR soft grip

Your cordless drill is equipped with TPR soft grip and protective parts. TPR (Thermoplastic

rubber) is elastic, chock absorbing and environmental friendly (recyclable).

9 OPERATION

9.1 Charging the battery pack

The battery pack for this tool is supplied in a low charge condition to prevent possible

problems, therefore, you have to charge the battery before first use.

Note: Batteries will not reach full charge the first time they are charged.

Allow several cycles for the item to fully charge. The battery should only be

charged indoors.

After normal use, about 1 hour of charging time is required for the battery to be fully charged.

The battery pack will become slightly warm while charging, this is normal and does not

indicate a problem.

Do not place the charger in an area of extreme heat or cold. Best is at normal room

temperature. When the battery becomes fully charged, unplug your charger from the power

supply and remove the battery pack from the charger.

Note:

 Allow the battery pack to cool completely before charging

 Inspect the battery pack before charging, do not charge a cracked or leaking battery pack.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWDP1510 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWDP1510

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info