Bedienungsanleitung Powerplus POWDP2510 (Seite 9 von 12) (Englisch)

676320

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

POWDP2510 EN

10.4 LED work-light (Fig. 8)

The LED work light (3) can light prior to motor running if you press the switch lightly, which

keep the work area to be lighted for checking clearly at first, and it lights also during your

operation.

NOTE: The LED work-light delay about 5s to extinguish after turn off the

tool.

WARNING: Do not stare directly at the light beam. Never aim the beam at

any person or an object other than the work piece.

Do not deliberately aim the beam at personnel and ensure that it is not

directed towards the eye of a person for longer than 0.25s.

11 GENERAL OPERATING INSTRUCTIONS

 Slide a fully charged battery pack into the bottom of the handle, making sure that it clicks

into place. Be sure the battery pack is securely seated into the saw handle so it will not fall

off during use.

 Firmly hold the reciprocating saw with both hands. Position the Blade near the work piece,

depress the lock-off button (5) and hold the ON/OFF switch trigger (6) down.

 Release the lock-off button once the tool has power. Allow the saw to come up to full

speed before addressing it to the work piece.

IMPORTANT: Do not start the saw if the saw blade is in contact with

anything before operation. If necessary, lift the tool from the work piece

before squeezing the ON/OFF switch trigger.

 In preparation for making a cut, place the pivot shoe assembly (1) on the surface to be cut.

Align the saw blade with the direction of the cut and slowly lower the saw blade onto the

cut line to begin the cut. Do not attempt to cut with the tip of the blade; kickback and

damage to the blade could result.

 When finished cutting, release the ON/OFF switch trigger to stop the tool.

 Remove the battery pack and the saw blade.

 Clean, then store the saw indoors and out of children’s reach.

11.1 General cutting

Clamp your work piece if it is portable. Rest the front shoe of the saw on your work piece (be

sure the blade is not contacting the work piece) and start the saw, exerting enough pressure in

the direction of the cut to keep the shoe pressed firmly against the work piece at all times. Do

not force the cut or stall the saw. Don’t bend or twist the blade, let the tool and the blade do

the work.

In general, coarser blades are for wood, plastics, and composites, and finer blades are for

cutting metal. Chattering or vibration may indicate you need a finer blade or higher speed. If

the blade overheats or clogs, it may indicate you need a coarser blade. Replace blades when

they become dull. Dull blades will produce poor results and may overheat the saw.

11.2 Plunge cutting

Clearly mark the line of cut, from a convenient starting point within the cut out area. Place the

tip of the blade over that point with saw parallel to the line of cut, slowly lower the saw until the

bottom edge of the shoe rests on the work piece and the blade is not touching the work piece.

Start the saw and allow it to attain full speed. With the saw resting on the shoe, slowly tilt the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWDP2510 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWDP2510

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info