Bedienungsanleitung Powerplus POWDP4050 (Seite 6 von 12) (Englisch)

795637

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

POWDP4050 EN

5.5 Service

 Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

6 ADDITIONAL SAFETY WARNINGS FOR PLANERS

 Before using the tool, make sure that the cutters have been properly mounted.

 Do not use the tool before It has been fully adjusted according to the Instructions.

 Before planing, let the tool run without load to check if the cutters are properly balanced.

 Never load the tool so much that the motor Is coming 1o a standstill,

 When planing, shavings may assemble in the grooves. Do not remove the shavings with

your hands - use a piece of wood,

 Only use the cutter cylinder and cutters supplied with the tool.

 Use original accessories only.

 Only use sharp cutters.

 If you want to make adjustments to the tool, switch it off, wait for the cylinder to come to a

standstill and unplug the tool,

 Switch off the tool and wait for the cutters to come to a standstill before putting the tool

down. Reduce the planing depth to avoid contact between the cutters and other objects.

7 ADDITIONAL SAFETY INSTRUCTIONS FOR BATTERIES AND

CHARGERS

Use only batteries and chargers applicable for this machine.

7.1 Batteries

 Never attempt to open for any reason.

 Do not store in locations where the temperature may exceed 40 °C.

 Charge only at ambient temperatures between 4 °C and 40 °C.

 Store your batteries in a cool dry place (5 °C-20 °C). Never store batteries in discharged

state.

 It is better for Li-ion batteries to discharge and reload them regularly (at least 4 times a

year). The ideal charge for long-term storage of your Li-ion battery is 40% of capacity.

 When disposing of batteries, follow the instructions given in the section “Protecting the

environment”.

 Do not cause short circuits. If connection is made between the positive (+) and negative (-)

terminal directly or via accidental contact with metallic objects, the battery is short circuited

and an intense current will flow causing heat generation which may lead to casing rupture

or fire.

 Do not heat. If batteries are heated to above 100 °C, sealing and insulating separators

and other polymer components may be damaged resulting in electrolyte leakage and/or

internal short circuiting leading to heat generation causing rupture or file. Moreover do not

dispose of the batteries in fire, explosion and/or intense burning may result.

 Under extreme conditions, battery leakage may occur. When you notice liquid on the

battery, proceed as follows:

 Carefully wipe the liquid off using a cloth. Avoid skin contact.

 In case of skin or eye contact, follow the instructions below:

 Immediately rinse with water. Neutralize with a mild acid such as lemon juice or

vinegar.

 In case of eye contact, rinse abundantly with clean water for at least 10 minutes.

Consult a physician.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWDP4050 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWDP4050

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info