Bedienungsanleitung Powerplus POWE00064 (Seite 9 von 13) (Englisch)

676025

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

POWE00064 EN

8.3.1 Rotation (right/left/lock)

Direction of rotation is controlled by the direction of rotation selector (4) located above the

switch trigger.

Right : To select forward rotation, release the on/off switch and push the forward/reverse lever

to the left side of the tool.

Left : To select reverse rotation, push the lever to the right side of the tool.

Lock: When the selector is in the center position, the switch trigger is locked. (See Fig. 5)

This helps to reduce the possibility of accidental starting when not in use

8.3.2 Variable speed

This tool has a variable speed switch that delivers higher speed and torque with increased

trigger pressure. The rotational speed is controlled by the amount of switch trigger depression.

8.4 Installing and Removing a Bit and a Drill (fig. 6)

This drill has a keyless chuck (1) to prevent the bit or drill from loosening.

1 Hold ring A of the drill chuck tight with one hand.

2 Turn upper ring B anticlockwise with the other hand until the drill chuck opening is large

enough to accept the tool.

3 Insert the drill or the screwdriver bit into the drill chuck.

4 Turn ring B clockwise until the tool is clamped tightly.

Remove the tool in the opposite way.

8.5 Adjusting the torque

The torque is adjusted by rotating the torque setting ring (2); the torque is greater when the

torque setting is set on a higher position. The torque is less when the torque setting ring is set

on a low position. Position“1”denotes the lowest and “ ” denote the highest.

The torque force is set by means of a torque setting according to the size of screw and the

kind of material. Select the suitable torque for the job to be performed .. long screws and/or

hard material require a higher torque setting.

8.6 Speed selector (Fig. 7)

NOTE： the L-mark is the “Low speed” position, the H-mark is the “High speed” position

(marks moulded in the button of two speed selector (3).)

The drill has a two-speed gear box designed for drilling at L (LOW) or H (HIGH) speed. The

gear selector is located on top of the drill to select either low or high speed. When you push

the button (5) forward and select low speed range, the speed will decrease but will provide

more power and torque.

When using the drill in the high speed range, the speed will increase but will provide less

power and torque. Use the low speed for high power and torque applications and the high

speed for fast drilling applications.

Important: NEVER adjust this two speed selector（3）while the drill is running. Always let it

come to a complete stop.

8.7 LED light (Fig. 8)

The LED work-light（9）can be lit prior to motor running.

Press the on/off switch lightly, to keep the work area lighted.

it also lights during operation.

NOTE: The LED work-light is switched off delayed with about 5sec.

WARNING:

Do not stare directly at the light beam. Never aim the beam at any person or an object other

than the work piece.

Do not deliberately aim the beam at personsl

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWE00064 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWE00064

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info