Bedienungsanleitung Powerplus POWE30040 (Seite 10 von 14) (Englisch)

675235

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

POWE30040 EN

 Place the material to be cut onto a flat surface such as a workbench, table or floor. Use a

piece of scrap material underneath if:

 You do not wish to damage the work surface.

 The work surface is likely to damage the blade. E.g. a concrete floor.

 Plug into mains supply.

 Grasp the tool firmly (See “Holding & switching ON/OFF” section) and rest its metal

base plate onto the surface to be cut. Ensure that the rear half of the base plate

overhangs the work surface. Do not plunge the blade into the material.

 Switch on the tool and wait for a moment for the blade to run up to speed. Next, depress

the safety lock button (3) and plunge the blade into the material slowly and gently, but

firmly. Then push the tool forwards along the line to be cut. If necessary, switch on the

laser generator (1).

 NOTE: Never draw the tool backwards.

 Very little force should be used to feed the tool along the cut. Excess force will cause

operator fatigue and excessive wear to the blade and tool. Excess force is also likely to

cause the temperature cut-out to trip, resulting in delays.

 Ensure that the base plate is always held flat on the material being cut. This is particularly

important at the start or finish of a cut or if thin strips are being cut where the base plate is

not fully supported.

 Once the cut has been finished, lift the tool from the work surface before switching off. If a

lot of dust has been created, keep switched on for a few seconds extra to allow the dust to

clear from within the tool.

12 CUT-OUTS

Plunge cutting may not be possible in some hard materials.

 Choose a suitable saw blade for hard materials and change to it. Set the depth of cut (See

“Setting the Cutting Depth” section), plug in the mains supply and then place the metal

base plate (16) onto the work surface. Ensure that the front indication mark on the base

plate aligns with the start line (See “Line Following” section).

 Switch on the tool and wait for a moment for the blade to run up to speed. Next, plunge

the blade into the material slowly and gently, but firmly. Then push the tool forwards along

the line to be cut. (Never draw the tool backwards)

 Once the finish line has been reached, lift the tool from the work surface before switching

off. If a lot of dust has been created, keep switched on for a few seconds extra to allow the

dust to clear from within the tool.

 Cutting out tips:

 If the cut is to be covered, for example by a vent cover, the corners can be overlapped to

ensure that the waste material is completely detached.

 If the cut out is to be seen, do not overlap the corners. In this circumstance, as the cutting

blade is circular, the waste material will not be fully detached. The corners will therefore,

require finishing with a knife. If the material is thin and the back surface unimportant, the

waste material can just be pushed out.

 Where there is access to the back surface of the material to be cut, the cut out can be

marked out with an over cutting allowance. The cut is then made from the back surface to

ensure perfect corners on the front surface.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWE30040 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWE30040

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info