Bedienungsanleitung Powerplus POWE40050 (Seite 4 von 7) (Englisch)

676335

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

POWE40050 EN

 If devices are provided for the connection of dust extraction and collection facilities, ensure

these are connected and properly used. Use of these devices can reduce dust related

hazards.

5.4 Power tool use and care

 Do not force the power tool. Use the correct power tool for your application. The correct

power tool will do the job better and safer at the rate for which it was designed.

 Do not use the power tool if the switch does not turn it on and off. Any power tool that

cannot be controlled with the switch is dangerous and must be repaired.

 Disconnect the plug from the power source before making any adjustments, changing

accessories, or storing power tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

 Store idle power tools out of the reach of children and do not allow persons unfamiliar with

the power tool or these instructions to operate the power tool. Power tools are dangerous

in the hands of untrained users.

 Maintain power tools. Check for misalignment or sticking of moving parts, breakage of

parts and any other condition that may affect the power tool’s operation. If damaged, have

the power tool repaired before use. Many accidents are caused by poorly maintained

power tools.

 Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to stick and are easier to control.

 Use the power tool, accessories and tool bits etc., in accordance with these instructions

and in the manner intended for the particular type of power tool, taking into account the

working conditions and the work to be performed. Use of the power tool for operations

different from intended could lead to a hazardous situation.

5.5 Service

 Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

6 ADDITIONAL SAFETY-HINTS FOR SANDERS

 Always wear safety-goggles and a dust-mask during your work with the finishing-sander.

 Always secure the work piece by clamps or else to avoid slipping away.

 Always keep the holes in the base plate clean from dust.

 Always connect a vacuum cleaner to the attached adaptor during your work.

 Take special care when sanding lead based paint:

 All persons entering the work area must wear a mask specially designed for protection

against lead paint dust and fumes.

 Children and pregnant women must not enter the work area.

 Do not eat, drink or smoke in the work area.

 Do not leave the tool running. Operate the tool only when hand-held.

 Ventilate your work area adequately when you perform sanding operations.

 Be sure that there are no cracks or breakage on the pad before use. Cracks or breakage

may cause a personal injury.

7 OPERATING INSTRUCTIONS

Do not sand plaster surfaces, (WARNING: In this case your guarantee

becomes void) this may clog the motor (brushes, ball bearings,…).

7.1 Switching On-off (Fig. 1)

 To start the machine, press the On/Off switch forward.

 To switch the machine off, press the On/Off switch to the rear.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWE40050 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWE40050

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info