Bedienungsanleitung Powerplus POWLI121 - ENERGY SAVING FLOODLIGHT (Seite 3 von 4) (Englisch)

640895

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

POWLI121 EN

7.3 LITE adjustment

 The LITE adjustment determines at what light level the lighting system will start

operating when you set the sensor to Automatic Operation.

 Provisionally turn the LITE control knob to the edge clockwise at the moon (dusk)

position. In this provisional setting mode, the motion sensor remains inactive during

daylight. At dusk when you find it is the LUX level desired for operation, simply set

the LITE control knob to the position that the motion sensor will become active as

daylight declines.

7.4 SENS adjustment

The sensitivity adjustment may be adjusted to compensate for seasonal variations in

temperature and to reduce unwanted triggering. The optimum sensitivity can be achieved

by setting the SENS. control knob initially to its mid-point and then adjusting the control

knob clockwise to increase (up to 12 meters) the detecting distance or anti-clockwise to

decrease (down to 3 meters) the detecting distance.

8 THE FIELD OF DETECTION

 The field of detection of the infrared sensor can be adjusted 30 degrees in horizontal

direction and 30 degrees in vertical direction. By means of horizontal adjustment, the

permanent 180° field of detection can be infinitely directed to the right or left (Fig.4).

By means of vertical adjustment the detection range can be reduced or expanded

(Fig. 5). This way any false detections caused by movements from neighbours and

from the street are excluded.

 The best detection is obtained by approaching the field of detection perpendicular to

its axis (Fig. 6).

 If the field of detection is approaching the direction of its axis, the infrared detector

will, in some cases, respond later (Fig. 7).

9 FIXING AND CHANGING AN ENERGY-SAVING LAMP

 Lamp tube fitting. Unscrew the bolt and open the glass holder. Fit the tube into the

tube socket.

 Then place the waterproof rubber pad in it’s original position and close the cover with

the bolt.

10 POSSIBLE PROBLEMS

 Ventilators, such as the discharge from a vapour cap or dryer (hot air movement) can

cause the lamp to switch on when it is not required to do so.

 Passing cars (warm engines) can also cause your lamp to switch on.

 Nearby trees and bushes, sudden changes in temperature and gusts of wind can

also cause the lamp to switch on.

 If the lamp has been placed under a roof or under trees, then the lamp can also burn

during daylight hours.

 If your lamp does not work then the bulb or fuse could be defective or there may have

been a failure in the electrical circuit.

 If the temperature difference between the object to be detected and surrounding area

is too small (in the summer for example), then your lamp will react later. The range of

detection is then 10 meters instead of 12 meters for example.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWLI121 - ENERGY SAVING FLOODLIGHT Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWLI121 - ENERGY SAVING FLOODLIGHT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info