Bedienungsanleitung Powerplus POWX0032 (Seite 6 von 11) (Englisch)

644871

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

POWX0032 EN

 Under extreme conditions, battery leakage may occur. When you notice liquid on the

battery, proceed as follows:

 Carefully wipe the liquid off using a cloth. Avoid skin contact.

 In case of skin or eye contact, follow the instructions below:

o Immediately rinse with water. Neutralize with a mild acid such

as lemon juice or vinegar.

o In case of eye contact, rinse abundantly with clean water for at

least 10 minutes. Consult a physician.

Fire hazard! Avoid short-circuiting the contacts of a detached battery. Do

not incinerate the battery.

6.2 Chargers (8)

 Use the charger provided with the tool only to charge the battery

 Never attempt to charge non-rechargeable batteries.

 Have defective cords replaced immediately.

 Do not expose to water.

 Do not open the charger.

 Do not probe the charger.

 The charger is intended for indoor use only.

7 FEATURES

7.1 Keyless chuck (1)

A keyless chuck is included on your drill to allow for easy installation and removal of

bits/accessories. The chuck is divided into two parts. The rear is called the collar and the front

is called the body.

To open and close the keyless chuck, grasp and hold the collar of the chuck with one hand

and rotate the chuck body with your other hand. The arrows on the chuck indicate in which

direction to rotate the chuck body in order to GRIP (tighten) or release (unlock) the drill bit.

WARNING: Do not hold the chuck body with one hand and use power of the

drill to tighten or loosen the juck jaws. The chuck body could slip and your

hand could come in contact with a rotating accessory. This could cause an

accident resulting in personal injury.

7.2 Torque adjustment ring (2)

The drill has a torque adjustment ring. It allows you to select the desired torque depending on

the task you have to perform (drill / different types of screws into different materials). The

proper setting depends on the type of material and the size of screw you are using.

TO ADJUST TORQUE: Identify the 21+1 torque indicator settings located on the front of the

drill. Rotate adjusting ring (2) to the desired setting. The lower the number, the lower the

torque setting. The higher the number, the higher the torque setting.

7.3 On/off switch (5)

To turn your drill ON, depress the switch trigger. To turn it OFF, release the switch trigger.

The switch trigger can be locked in the OFF position. This feature helps reduce the possibility

of accidental starting when not in use.

7.4 Forward/reverse selector (right/left rotation selector) (4)

The drill has a forward/reverse selector located above the switch trigger.

 F(Forward) (Forward): Press selector on right side of machine (to the left side): drill turns

right (forward, fasten screws)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX0032 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX0032

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info