Bedienungsanleitung Powerplus POWX0047LI (Seite 7 von 12) (Englisch)

644875

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

POWX0047LI EN

7.4 On/off switch (5)

To turn your drill ON, depress the switch trigger. To turn it OFF, release the switch trigger.

The switch trigger can be locked in the OFF position. This feature helps reduce the possibility

of accidental starting when not in use.

7.5 Forward/reverse selector (right/left rotation selector) (4)

The drill has a forward/reverse selector located above the switch trigger.

 F(Forward) (Forward): Press selector on right side of machine (to the left side): drill turns

right (forward, fasten screws)

 R(Reverse) (Reverse): Press selector on left side of machine (to the right side): drill turns

left (reverse/ loosen screws)

CAUTION: To prevent damage to the gearbox, always allow the chuck to

come to a complete stop before changing the direction of rotation or

selecting another speed (HI-LO). To stop, release the trigger switch.

7.6 Speed selector (3)

Your cordless drill has a two-speed gear, designed for drilling or driving at LO or HI speed. A

slide switch is located on top of your drill to select either LO (1) or HI (2) speed.

The low speed (LO) is used, in combination with the torque setting, for screwing screws in or

out and for drilling with a larger diameter.

The high speed (HI) is used only for drilling (never for screwing, as this may lead to damage of

the tool).

7.7 LED worklight (6)

Your cordless drill is equipped with an LED light at the front (above the ON/OFF switch) above

the battery pack. The white LED light will light when you operate the machine, providing the

work area to be lighted.

7.8 TPR soft grip

 Your cordless drill is equipped with TPR soft grip and protective parts. TPR

(Thermoplastic rubber) is elastic, chock absorbing and environmental friendly (recyclable).

8 (PRE)OPERATION

8.1 Battery charging

Use only the battery charger supplied with your tool. Only these battery chargers are matched

to the lithium ion battery of your power tool.

Note: The battery is supplied partially charged. To ensure full capacity of

the battery, completely charge the battery in the battery charger before

using your power tool for the first time. The lithium ion battery can be

charged at any time without reducing its service life. Interrupting the

charging procedure does not damage the battery.

Charging procedure 1h:

 Adapt the charger to the mains. The green led will light up, the red led remains unlit.

 Place the battery in the charger. The green led will go out, the red led will light up.

 When the battery is fully charged (after 1 hour), the green led will light up again and the

red led will go out!

 The battery indicator leds on the tool (yellow, green red), will show the battery status

when pressing the on/off trigger (5). When only the red led is lit, the battery needs

recharging.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX0047LI Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX0047LI

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info