Bedienungsanleitung Powerplus POWX0076LI (Seite 7 von 11) (Englisch)

582660

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

POWX0076LI EN

 Do not cause short circuits. If connection is made between the positive (+) and negative (-)

terminal directly or via accidental contact with metallic objects, the battery is short circuited

and an intense current will flow causing heat generation which may lead to casing rupture

or fire.

 Do not heat. If batteries are heated to above 100 °C, sealing and insulating separators

and other polymer components may be damaged resulting in electrolyte leakage and/or

internal short circuiting leading to heat generation causing rupture or file. Moreover do not

dispose of the batteries in fire, explosion and/or intense burning may result.

 Under extreme conditions, battery leakage may occur. When you notice liquid on the

battery, proceed as follows:

 Carefully wipe the liquid off using a cloth. Avoid skin contact.

 In case of skin or eye contact, follow the instructions below:

 Immediately rinse with water. Neutralize with a mild acid such as lemon juice or

vinegar.

 In case of eye contact, rinse abundantly with clean water for at least 10 minutes.

Consult a physician.

Fire hazard! Avoid short-circuiting the contacts of a detached battery. Do

not incinerate the battery.

8.2 Chargers

 Use the charger provided with the tool only to charge the battery

 Never attempt to charge non-rechargeable batteries.

 Have defective cords replaced immediately.

 Do not expose to water.

 Do not open the charger.

 Do not probe the charger.

 The charger is intended for indoor use only.

9 ADJUSTMENTS

Always disconnect the battery pack from the cordless circular saw before

making any adjustment or attaching any accessories.

9.1 Replacing the saw blade (Fig. 1)

Only use sharp and undamaged saw blades. Cracked or bent saw blades must be replaced

immediately.

 Place this circular saw on its side on a flat surface. Advice you bring the base plate (10)

down as if a minimum depth cut which is ease to operate.

 Push the spindle lock button toward motor housing as the arrow shows in Fig. 1 and firmly

hold it.

 Turn the blade clamp bolt anti-clockwise by using the Allen key that supplied with the tool.

 Remove the blade clamp bolt and outer flange.

 Raise the lower guard (16) by using the lever for lower guard (17), and then remove the

saw blade.

 Clean the saw blade flanges, then mount the new saw blade onto the output spindle and

against the inner flange.

 Make sure the saw teeth and arrow on the blade is to be the same direction as the arrow

on the lower guard.

 Reinstall the outer flange, and tighten the blade clamp bolt.

 Make sure that the saw blade runs freely by turning the blade by hand.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX0076LI Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX0076LI

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info