Bedienungsanleitung Powerplus POWX05201 (Seite 6 von 10) (Englisch)

645072

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

POWX05201 EN

6 SPECIFIC SAFETY WARNINGS FOR CIRCULAR SAWS

 Make sure that all devices screening the saw blade are in perfect working order.

 Make sure that the saw blade is screened correctly. Especially observe the following

instructions:

 Never block the saw blade guard. Repair a jammed saw blade guard before using the

machine again.

 Replace a broken tension spring before using the machine again.

 Never remove the riving knife. The distance between the toothed rim and the riving knife

should be 5 mm maximum. The height difference between the riving knife and the

toothed rim should be 5 mm maximum.

 Do not use saw blades made of HSS steel.

 Do not use bent, deformed or otherwise damaged saw blades.

 Do not use saw blades which do not meet the specifications stated in this manual.

 Before sawing, remove all nails and other metal objects from the workpiece.

 Never start sawing before the saw reaches its full speed.

 Securely clamp the workpiece. Never attempt to saw extremely small workpieces.

 Only put the machine aside after switching off and when the saw blade has come to a

complete standstill.

 Never try to slow the saw blade down by exerting pressure on the side.

 Before performing maintenance to the machine, always unplug the machine.

7 ASSEMBLY

7.1 Replacing the saw blade (Fig. 1)

Only use sharp and undamaged saw blades. Cracked or bent saw blades must be replaced

immediately.

 Place this circular saw on its side on a flat surface. Advice you bring the base plate (10)

down as if a minimum depth cut which is ease to operate change the blade.

 Push the spindle lock button toward motor housing as the arrow shows in Fig. 1 and firmly

hold it.

 Turn the blade clamp bolt anti-clockwise by using the spanner the hex key that supplied

with the tool.

 Remove the blade clamp bolt and outer flange.

 Raise the lower guard (12) by using the lever for lower guard (1), and then remove the

saw blade.

 Clean the saw blade flanges, then mount the new saw blade onto the output spindle and

against the inner flange.

 Make sure the saw teeth and arrow on the blade is to be the same direction as the arrow

on the lower guard.

 Reinstall the outer flange, and tighten the blade clamp bolt.

 Make sure that the saw blade runs freely by turning the blade by hand.

Before replacing the saw blade always unplug the tool.

7.2 Depth adjustment (Fig. 2)

 Loosen the adjusting screw lock lever for depth adjustment (7).

 Hold the base plate (10) flat against the edge of the work piece and lift the body of the saw

until the blade is at the right depth determined by the depth gauge of cut scale (4) (align

the scale line).

 Tighten the adjusting screw the lock lever for depth adjustment.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX05201 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX05201

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info