675011
8
Zoom out
Zoom in
Vorherige Seite
1/19
Nächste Seite
POWX07551T EN
Copyright © 2016 VARO P a g e | 8 www.varo.com
Loosen the screw with a Phillips screwdriver.
Place the hold-down clamp (B) in the desired mounting hole.
Tighten the screw to hold the hold-down clamp.
8.4 Saw blade wrench (Fig. 4)
For convenient storage and prevention of loss, there is a slot in the side of the switch
handle for storing the blade wrench (D) when not in use.
8.5 Inserting and replacing batteries for the laser (Fig. 4)
Unplug your mitre saw
WARNING! Failure to unplug your tool could result in accidental starting
causing possible serious personal injury.
Open the battery cover located on the switch handle.
Insert two AAA batteries (F) as per the diagram. If replacing the batteries, take out the old
batteries and replace with new AAA batteries. Dispose of old batteries properly.
Close the battery cover.
NOTE: Replace with batteries that have a rating of 1.5 volts (Number 4
series and AAA size or equivalent).
HELPFUL HINT: Remove the two batteries during long periods of non-use
of the saw. This will reduce damage to the laser guide from the batteries
corroding during storage.
8.6 Unlocking the slide carriage (Fig. 5)
After removing the saw from the carton, loosen the slide carriage lock knob (1). When
transporting or storing the mitre saw, the slide carriage should always be locked in
position. The slide carriage lock knob (1) is located on the right side of the slide carriage.
8.7 Unlocking and locking the cutter head (Fig. 6)
Unlocking the cutter head:
To raise the cutter head from its storage/transport position: push down slightly on the
switch handle (1).
Pull out the stop latch knob (2).
Allow the cutting head to rise to the up position.
Locking the cutter head:
When transporting or storing the mitre saw, the cutting head should always be locked in the
down position.
Push the cutting head down to its lowest position.
Push the stop latch knob (2) into the locking hole.
CAUTION: To avoid injury and damage to the saw, transport and store the
mitre saw with the cutting head locked in the down position. Never use the
stop latch to hold the cutting head in a down position for cutting
operations.
IMPORTANT: To avoid damage, never carry the mitre saw by the switch
handle, the cutting arm or the mitre table handle. ALWAYS use the hand
holds for transportation.
8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Powerplus POWX07551T wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Powerplus POWX07551T

Powerplus POWX07551T Bedienungsanleitung - Deutsch - 21 seiten

Powerplus POWX07551T Bedienungsanleitung - Holländisch - 21 seiten

Powerplus POWX07551T Bedienungsanleitung - Französisch - 21 seiten

Powerplus POWX07551T Zusatzinformation - Alle Sprachen - 8 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info