Bedienungsanleitung Powerplus POWX07551T (Seite 14 von 19) (Englisch)

675011

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

POWX07551T EN

WARNING! To avoid injury, after completing a cut and releasing the trigger

switch, wait and confirm the blade has stopped before raising the cutting

head. To avoid injury, check and tighten the arbor bolt periodically.

9.2 Sliding carriage system (Fig. 22)

 For chop cutting operations on small workpieces, slide the cutting head assembly

completely toward the rear of the unit and tighten the carriage lock knob (1).

 To cut wide boards up to 8 in., the carriage lock knob (1) must be loosened to allow the

cutting head to slide freely.

9.3 Mitre cut (Fig. 23)

 When a mitre cut is required, unlock the mitre table by turning the mitre handle (1)

counterclockwise.

 While holding the mitre handle, lift up on the positive stop locking lever (2).

 Rotate the mitre table to the right or left with the mitre handle.

 When the table is in the desired position, as shown on the mitre scale (3), release the

positive stop locking lever and tighten the mitre handle. The table is now locked at the

desired angle. Positive stops are provided at 0°, 15°, 22.5°, 31.6° and 45°.

IMPORTANT: Always tighten the mitre tablelock handle before performing

every cutting operation.

9.4 Bevel cut (Fig. 24)

 When a bevel cut is required, loosen the bevel lock handle (1) by turning it clockwise.

 Tilt the cutting head to the desired angle, as shown on the bevel scale (2).

 The blade can be positioned at any angle, from a 90° straight cut (0° on the scale) to a 45°

left bevel. Tighten the bevel lock handle (1) to lock the cutting head in position. Positive

stops are provided at 0° and 45°.

9.5 Compound cut (Fig. 25)

A compound cut is the combination of a mitre and a bevel cut simultaneously.

 Loosen the bevel lock handle (1) and position the cutting head at the desired bevel

position. Lock the bevel lock handle (1).

 Loosen the mitre handle (2). Lift up the positive stop locking lever (3) and position the

table at the desired angle. Release the positive stop locking lever (3) and lock the mitre

handle (2).

9.6 Slide cutting wide boards (Fig. 26)

CAUTION: Always use a work clamp to maintain control and reduce the risk

of workpiece damage and personal injury.

WARNING! To avoid injury: 1) Let the blade reach full speed before cutting.

This will help reduce the risk of a thrown workpiece. 2) Do not make

crosscuts by lowering the blade and pulling the saw head through the wood

toward you. The blade may try to climb up on top of the workpiece, causing

the cutting assembly and spinning blade to kick back forcefully.

 Unlock the carriage lock handle (1) and allow the cutting head assembly to move freely.

 Set both the desired bevel angle and/or the mitre angle and lock into position.

 Use a hold down clamp (2) to secure the workpiece (3).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX07551T Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX07551T

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info