Bedienungsanleitung Powerplus POWX07562 (Seite 6 von 11) (Englisch)

675015

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

POWX07562 EN

5.5 Service

 Your power tool should be serviced by a qualified specialist using only standard spare

parts. This will ensure that it meets the required safety standards.

6 ADDITIONAL SAFETY INSTRUCTIONS FOR LASERS

 Warning! The laser beam potentially causes severe eye damage. Never look or stare

directly into the laser beam.

 During use, do not point the laser beam at people, directly or indirectly through reflecting

surfaces.

 This laser complies with class 2 according to EN 60825-1:2001. The unit includes no

servicing components. Do not open the housing for any reason. If the unit is damaged,

have the damage repaired by an authorized repair agent.

7 ADDITIONAL SAFETY INSTRUCTIONS FOR BATTERIES

 When replacing batteries, always replace the complete set. Do not mix old batteries with

new ones.

 Prevent removed batteries from short circuiting.

 Do not store batteries where the temperature may rise above 50 °C, e.g. in a car which

has been parked in the sun.

 Do not burn batteries.

 Never attempt to open batteries.

 In case of battery leakage, carefully remove the liquid using a cloth. Avoid skin or eye

contact. Do not swallow. In case of skin or eye contact, rinse abundantly for 10 minutes

with clean water and consult a physician.

8 ASSEMBLY

8.1 Setting up the saw (Fig.1)

 Insert the two workpiece support clips (11) in the mounts (12) provided on the side of the

tool and fasten them in place with the screws (13).

 Insert the clamping device (14) into one of the two mounts (15) provided on the top of stop

rail and fasten in place with the thumb screw (16).

 Screw the additional stability bar (17) to the back of the machine.

8.2 Adjusting the saw (Fig. 2)

 The rotary table (8) has latching positions at 0°, 15°, 22.5°, 30° and 45°. You can adjust

the angle by moving the table to the left or to the right using the handle (24).

 While pressing down lightly the machine head (4), pull the lock pin (20) out of the motor

holder to disengage the saw from its bottom working position.

 Swing up the machine head until the retaining hook latches home.

 By loosening the lock screw (10), the machine head (4) can be angled to the left up to 45°.

 Check that the voltage marked on the rating plate is the same as your mains voltage and

connect up the machine.

8.3 90° cross-cuts and 0° rotary table (Fig. 3)

 To turn the machine on press the on/off switch (1)

 Important! Place the material you want to saw flat on the machine surface and secure with

the clamping device (14) so that the material cannot move while you are cutting.

 After switching on the saw, wait for the blade (5) to reach its maximum speed.

 Press the release lever (1) sideways and, using the handle (3), apply steady and light

downward pressure to move the machine head through the workpiece.

 When the cut is completed, return the machine to its top parking position and let go of the

On/Off switch.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX07562 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX07562

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info