Bedienungsanleitung Powerplus POWX07582 (Seite 8 von 20) (Englisch)

675035

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

POWX07582 EN

9.1 Installation

 Get help from another person for lifting the machine out of the box.

 Turn the turntable into the 0° position and tighten up the mitre locks.

Note: If the machine must be mounted on a workbench, then the rubber feet should NOT be

installed.

You run the risk of injury, if you handle the machine incorrectly when lifting

or turning it. Always hold the machine firmly by the base (12).

 Position the machine on a suitable surface:

 All 4 feet must rest firmly on the surface.

 The ideal height of the surface is approximately 800 mm.

 The saw must stand firmly in position, even when larger workpieces are being sawn.

 You can keep the packaging for future use, or you can dispose of it separately, based on

the type of material, and it in an environmentally friendly manner.

9.2 Transport

 Push the table saw downwards and at the same time pull out the locking knob (22) to lift

the table saw upwards.

 Position the lower saw blade guard (14) over the saw guide piece (21) and push

backwards until you hear a click, and until the lower saw blade guard is positioned at the

black line on the saw guide piece.

 Lower the saw head by pushing in the safety lock (6) and activate the locking pin (22).

 Position the mitre guide (4) over the lower saw blade guard and fasten it.

 Lift the machine up by grasping both sides of the base (12).

Note:

 The essential operating components of the machine are presented in this section.

 Make sure to read this section, before you use the machine for the first time.

9.2.1 Table saw operating mode

 Make sure that the table is mounted completely and in the right direction – see Paragraph

9.2 on Transport above - and that the locking pin (22) is properly locked.

 Remove the mitre and width guide (4).

 Install the saw blade guard (3) by sliding the back into the slot on top of the riving knife (2)

and backwards to lock. Mount the lower saw blade guard (14) by pushing the back of the

saw blade guard into the back of the opening of switch B (29)until the front of the lower

blade guard (14) is aligned with the reference points on the insert (21).

 The ON/OFF switch (7) is used for starting and stopping the machine.

9.2.2 Cross-cut and mitre saw operating mode

 Make sure that the mitre and width guide (4) is correctly installed and that the saw blade is

covered. This activates switch A (8). Make sure that the cover (mitre and width guide) is

firmly attached. If this is not the case, use the mitre and width guide locking knob (5) to

fasten it.

 Push the table saw downwards and at the same time pull out the locking knob (22) to lift

the table saw upwards.

 Remove the lower saw blade guard (14).

 For starting the motor, push on the switch (29) in the handgrip.

 To switch off the motor, release the switch (20).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX07582 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX07582

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info