480927
18
Zoom out
Zoom in
Vorherige Seite
1/23
Nächste Seite
POWX0782 EN
Copyright © 2015 VARO P a g e | 18 www.varo.com
Remove the shaft bolt (E1) and the outer saw flange (E2) from the saw shaft.
Remove the saw blade (18) from the saw shaft and lift it up to remove it from the machine.
Remove the shaft nut (E4) and the inner saw flange (E3) from the saw shaft.
Clean the surfaces of the following components:
-The saw shaft
-The inner saw flange
-The saw blade
-The outer saw flange
-The shaft nut
-The saw blade guard
HAZARD! Do not use any cleaning products (for instance for removing resin
residues) that have the tendency to cause corrosion on light metals; this
could damage the machine.
Fasten the shaft nut (E4) of the inner saw flange (E3) on the saw shaft.
HAZARD! Be sure to fasten the inner saw flange correctly! The saw may
block, or the saw blade may come lose, if the flange is not correctly
fastened. The inner saw flange is correctly mounted when the bevelled
collar (Q1) points to the right and the spring groove points to the left (Fig.
21).
Mount the new saw blade (18) and check the rotating direction (the arrow on the saw
blade must point in the same direction as the arrow on the saw blade guard!).
HAZARD! Only use saw blades that conform to the applicable standards
and that can be used at the maximum speed indicated in the technical data
sheet.
DO NOT use:
- Wrong saw blades
- Saw blades made of high-speed steel (HSS)
- Damaged saw blades
- Saw blades with missing teeth
HAZARD!
Only use OEM components for installing the saw blade.
- Do not use loose reduction rings; the saw blade could come loose.
- Saw blades must be mounted in such a way that they cannot wobble, and that they cannot
come loose during operations.
Install the outer saw flange (E2).
The two flanges must fit over the surfaces of the saw shaft.
Insert the shaft bolt (E1) (left-turning thread) and tighten with a hexagonal spanner.
HAZARD!
Do not lengthen the spanner, so that you can exercise more power.
Do not hit on the spanner with a hammer, for tightening the shaft.
18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Powerplus POWX0782 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Powerplus POWX0782

Powerplus POWX0782 Bedienungsanleitung - Deutsch - 24 seiten

Powerplus POWX0782 Bedienungsanleitung - Holländisch - 23 seiten

Powerplus POWX0782 Bedienungsanleitung - Französisch - 24 seiten

Powerplus POWX0782 Zusatzinformation - Alle Sprachen - 5 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info