480958
6
Zoom out
Zoom in
Vorherige Seite
1/10
Nächste Seite
POWX131 EN
Copyright © 2015 VARO P a g e | 6 www.varo.com
Keep mains lead clear from working range of the machine. Always lead the cable away
behind you.
The base plate must not be clamped down while the blade is extended. Lowering and
raising the blade must be a smooth operation,
7 ADJUSTMENTS
7.1 Adjusting the cutting depth
Move the motor base (14) as far as possible backwards.
Set the cutting depth by luring the cutting depth adjustment knob (6).
Move the motor base forwards and check if the pin will fall in the notch of the adjustment
knob.
7.2 Adjusting the cutting angle
The cutting angle can be set by unlocking the clamping knob (7} and put the angle stop (4)
in the required angle.
7.3 Adjusting the height
The correct height can be set by unlocking The clamping Knob (8) and turning The knob
for the height adjustment (9) to the desired height with aid of the scale (10)
The height must corresponds to half of the material Thickness of the work piece, the
groove lot the biscuit dowel must always be in The middle of the working piece
8 ASSEMBLAGE
ATTENTION! Disconnect the power plug before carrying out any
adjustments or maintenance..
8.1 Mounting saw blade
Loosen your screws and open the top of the base plate
Press the spindle lock and turn the spindle until it engages in the lock. Keep the spindle
lock pressed during this procedure.
Remove the flange nut from The spindle using the wrench.
Position the saw blade and the flange.
Place the flange nut from the spindle and tighten II with The wrench.
Take care that the flange nut will be placed with the correct aide on the spindle.
Release the spindle lock and check that the spindle is unlocked by rotating it.
Close the top of the base plate and fasten four screws.
Make sure that the top of the base plate is securely closed before operating
the machine.
8.2 Mounting dust bag
For dust extraction the dust bag can be used. Insert the dust bag into the vacuuming
Connection. Empty the dusts bag regularly so that the vacuuming performance remains intact.
9 OPERATION
9.1 Switching on and off.
Never use the spindle lock until the machine is working.
To switch the machine on slide the on/off switch forwards.
To switch the machine off, depress the on/off switch, the switch will automatically move in
the "off" position.
6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Powerplus POWX131 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Powerplus POWX131

Powerplus POWX131 Bedienungsanleitung - Deutsch - 11 seiten

Powerplus POWX131 Bedienungsanleitung - Holländisch - 11 seiten

Powerplus POWX131 Bedienungsanleitung - Holländisch - 11 seiten

Powerplus POWX131 Bedienungsanleitung - Französisch - 11 seiten

Powerplus POWX131 Zusatzinformation - Alle Sprachen - 1 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info