Bedienungsanleitung Powerplus POWX1365MB (Seite 9 von 14) (Englisch)

582667

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

POWX1365MB EN

11 CUT-OUTS

 Plunge cutting may not be possible in some hard materials.

 Choose a suitable saw blade for hard materials and change to it. Set the depth of cut (See

“Setting the Cutting Depth” section), plug in the mains supply and then place the metal

base plate (18) onto the work surface. Ensure that the front indication mark on the base

plate aligns with the start line (See “Line Following” section).

 Switch on the tool and wait for a moment for the blade to run up to speed. Next, plunge

the blade into the material slowly and gently, but firmly. Then push the tool forwards along

the line to be cut. (Never draw the tool backwards)

 Once the finish line has been reached, lift the tool from the work surface before switching

off. If a lot of dust has been created, keep switched on for a few seconds extra to allow the

dust to clear from within the tool.

 Cutting out tips:

I. If the cut is to be covered, for example by a vent cover, the

corners can be overlapped to ensure that the waste material is

completely detached.

II. If the cut out is to be seen, do not overlap the corners. In this

circumstance, as the cutting blade is circular, the waste material

will not be fully detached. The corners will therefore, require

finishing with a knife. If the material is thin and the back surface

unimportant, the waste material can just be pushed out.

III. Where there is access to the back surface of the material to be

cut, the cut out can be marked out with an over cutting allowance.

The cut is then made from the back surface to ensure perfect

corners on the front surface..

12 CUTTING PARTICULARLY TOUGH OR ABRASIVE MATERIALS

Learn to use the tool by cutting wood before attempting to cut anything tougher. When cutting

tougher material, such as metals, more force is required to hold the work piece and clamping

may be required.

Never cut materials that produce toxic dust or fumes such as PTFE or asbestos.

12.1 Sheet metal:

 Always set the depth adjustment to at least 1 mm deeper than the material thickness to

avoid the blade riding up over the surface. Scrap material is required underneath the work

surface.

 Remove burrs and rust as these impede the feed across the material.

 Thick beeswax (furniture polish) applied to the base plate of the tool makes metal cutting

easier.

 Only suitable for cutting brass, copper, lead, aluminium or galvanised mild steel.

 Every 2 minutes of metal cutting should be followed by a rest of at least 3 minutes.

12.2 Ceramic tiles, slates etc:

 Only use a blade specifically designed for this purpose.

 Always use with a suitable vacuum cleaner or dust extractor connected as the dust can be

hazardous to the operator and prevent the guard operating correctly.

12.3 Plasterboard:

 The plunge saw is only recommended for making occasional cut outs in plasterboard and

always us it with a suitable vacuum cleaner or dust extractor connected. The dust can

prevent the guard operating correctly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX1365MB Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX1365MB

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info