Bedienungsanleitung Powerplus POWX1410 (Seite 5 von 10) (Englisch)

645229

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

POWX1410 EN

 Hold power tool by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring or its own cord.

 When ripping always use a rip fence or straight edge guide.

 Always use blades with correct size and shape (diamond versus round) of arbour holes.

 Never use damaged or incorrect blade washers or bolt.

7 CAUSES AND PREVENTION OF KICKBACK

 A kickback is the sudden reaction as a result of a stuck, jammed or misaligned saw blade

which leads to an uncontrolled saw to be lifted and moved from the workpiece out in the

direction of the operator.

 A kickback can occur when the saw blade gets stuck or jammed in the saw gap. The saw

blade is blocked and the motor force repels the circular saw in the direction of the

operator.

 A kickback can occur when the saw blade becomes twisted or misaligned in the saw

groove. As a result, the teeth of the back edge of the saw blade can get stuck in the

surface of the workpiece, whereby the saw blade is moved out of the saw gap and the saw

jumps back in the direction of the operator.

 A kickback is the result of incorrect or faulty use of the saw. It can be prevented by

appropriate precautions as described below.

 Hold the saw firmly and bring your arm into a position in which you can resist the kickback

forces. Always hold the saw blades on the sides, never bring the blade in line with your

body. In a kickback, the saw can jump backwards, but the operator can control the

kickback forces if appropriate measures were taken.

 If the saw blade jams or sawing is interrupted for any reason, release the ON / OFF switch

and calmly hold the saw in the material until the saw blade stands completely still. Never

attempt to remove the saw from the workpiece or pull it backwards as long as the saw

blade is moving or a kickback might occur. Find the cause of the saw blade jam and

eliminate them through appropriate measures.

 When you want to restart a saw that is stuck in a workpiece, center the saw blade in the

saw gap and check that the saw teeth are not stuck in the workpiece. If the saw blade

jams, it can move out from the workpiece or a kickback can happen if the saw is restarted.

 Prop up large panels in order to minimise the risk of a kickback by a jammed saw blade.

Large panels tend to sag under their own weight. Panels must be supported on both sides,

both in the vicinity of the saw gap as well as on the edge.

 Do not use dull or damaged saw blades. Saw blades with blunt or misaligned teeth cause

increased friction, jamming of the saw blade and kickback by an excessively narrow saw

gap.

 Tighten the cutting depth position prior to cutting. If the settings change while cutting, the

saw blade can jam and a kickback can occur.

 Be especially careful if you perform a "circular cut" in a hidden area, such as an existing

wall. The protruding saw blade can get blocked in hidden objects while cutting and cause

a kickback.

 Do not place the saw on the workbench or the floor unless the saw blade is at a standstill.

An unprotected, running saw blade moves the saw against the cutting direction and cuts

whatever is in its way. Thus note the delay time of the saw.

 For this reason, the saw is not suitable for use in reverse position as fixed equipment.

 Do not operate the saw if it is not working properly or has been damaged. In case of

technical problems, do not attempt to repair it on your own. Contact the service or have

the saw repaired by a professional.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX1410 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX1410

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info