Bedienungsanleitung Powerplus POWX221 (Seite 8 von 13) (Englisch)

675037

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

POWX221 EN

7.3 Assemble undercarriage Fig. G

 Turn the machine upside down.

 Remove the black plastic bottom plate by unscrewing the 6 screws. (Fig. G-1).

 Unscrew the adjusting knob on the front and tilt the motor (Fig. G-2), then remove the

transport packing (Fig. G-3).

 Now place one by one the uprights in the casing of the sawing bench (Fig. G-4).

 Secure the uprights with 4 screws using a screwdriver, do not completely tighten the

screws (Fig. G-5).

 Fit the 4 support bars, do not completely tighten the screws (Fig. G-6)

 Fit the black plastic bottom plate and screw it tight.

 Attach the rubber feet under the uprights (Fig. G-7).

 Turn the machine into an upright position on a flat surface and adjust the machine so that

it stands in a stable position, tighten all the nuts and bolts (Fig. G-7).

7.4 Assemble bracket/push stick.

 Attach the 2 brackets onto t he casing of the sawing bench and screw them tight (Fig. G-

8).

 Place the push stick in the brackets.

7.5 Assembly and attachment of the rip fence Fig. D

 Attach the aluminium fence (A) to the positioning block (B).

 Now you can attach the complete rip fence to the bench top.

 Slide the rip fence via one end of the positioning rail (C) over the bench top.

 Adjust the position of the aluminium fence profile (A) such that the end corresponds to the

rear edge of the saw.

7.6 Assembly of the riving knife and the protective cap Fig. E

 Turn the saw blade completely upwards.

 Remove the bench inlay.

 Assemble the riving knife on the set-up for this purpose and use hereby the Allen screws

and the filling rings. Ensure that the riving knife falls properly into the opening (= groove).

 Now put the inlay back in the bench and fasten it.

 Now assembly the protective cap onto the riving knife and use hereby the profiled nut and

self-locking nut.

Now lay a lath against the saw blade and the riving knife and check whether

it falls properly into the extension of the saw blade. If this is not the

case:Loosen the fastening bolts and place or remove the filling rings.

 Above the saw table the radial distance between the riving knife and the toothed rim of the

saw blade shall not at any point exceed 5 mm at the depth of cut set.

 The tip of the riving knife shall not be lower than 5 mm from the tooth peak, as shown.

7.7 Assembly of the saw blade

First remove the plug from the mains before the saw blade is assembled or

replaced.

 Remove the inlay from the bench. Use a screwdriver for this purpose.

 Turn the saw axle completely upwards. Remove the nut and the outside flange from the

saw axle.

 Now slide the saw blade over the saw axle and now put the outside flange and the nut

back. Tighten the nut by hand.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX221 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX221

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info