Bedienungsanleitung Powerplus POWX358 (Seite 8 von 12) (Englisch)

645717

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

POWX358 EN

8.1 Adjusting the material volume (Fig. 6)

Set the material volume by turning the regulator knob on the trigger.

Set the material volume by turning the regulator on the trigger guard of the spray gun.

- turn to downside lower material volume.

+ turn to upside higher material volume.

Remark: It is advisable to test the spray gun on cardboard or a similar

surface to find the correct setting. Important: Begin spraying outside of the

target area and avoid interruptions inside the target area.

8.2 Spray technique

 The spray result depends heavily on the smoothness and cleanliness of the surface to be

sprayed. Therefore the surface should be carefully prepared and kept free of dust.

 Cover all surfaces not to be sprayed.

 Cover screw threads or similar parts of the target object.

 Correct (Fig. 7a): Be sure to hold the spray gun at an even distance of approx. 20 – 30 cm

to the target object.

 Incorrect (Fig. 7b): Heavy spray fog build-up, uneven surface quality.

 An even movement of the spray gun results in an even surface quality.

 When coating material builds up on the nozzle (A) and air cap (B) (Fig. 8), clean both parts

with a solvent or water.

9 TAKING OUT OF OPERATION AND CLEANING

 Turn the machine off. Activate the trigger guard so that the coating material in the spray

gun flows back into the container.

 Unscrew the container. Empty any remaining coating material back into the material tin.

 Pre-clean the container and feed tube with a brush.

 Pour solvent or water into the container. Screw the container back on.

 Use only solvents with a flashpoint over 21 °C.

 Turn on the machine and spray the solvent or water into a container or a cloth.

 Repeat the above procedure until the solvent or water emerging from the nozzle is clear.

 Turn the machine off.

 Then empty the container completely. Always keep the container seal free of coating

material residue and check for damage.

 Press down the quick release button (A) and pull out the front part of the spray gun. Clean

it thoroughly. Disassemble the nozzle parts and clean each part separately (Fig. 9).

 Clean the outside of the spray gun and container with a cloth soaked in solvent or water.

 Reassemble the nozzle back onto the sprayer (Fig. 10).

Caution! Never clean nozzle or air holes in the spray gun with sharp metal

objects.

10 MAINTENANCE

10.1 Change the air filter (Fig. 11)

Change the air filter (A)if it is soiled. Release the cover fastening from the machine, place the

air filter in the cover. Push the cover back onto the machine.

WARNING! Never operate the machine without the air filter; dirt could be

sucked in and interfere with the function of the machine.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX358 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX358

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info