Bedienungsanleitung Powerplus POWX513 (Seite 7 von 16) (Englisch)

675263

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

POWX513 EN

8.3 Assembly of handle clamp and handle

 Slide the clamp over the cross bar until the holes in the handle correspond with the holes

in the cross bar. Fix the clamp with the supplied M6x60 bolt and nut. (Fig 1)

 Attach the holder of the handle on the top tube with two supplied bolts M8x35 and M8 nuts

in the foreseen holes. Please note that the open side of the holder should face down.

Mount the handle in the holder with the supplied spindle bolt and M6 nut. (Fig 2)

8.4 Assembly wheels

Slide every wheel over an axle. Put a cotter pin in the bore of every wheel axle and bend the

ends of the cotter pin to fix.

9 CONTROL FUNCTIONS

9.1 Recoil starter

To start the engine, pull the starter grip lightly until resistance is felt, then pull briskly.

Do not allow the starter grip to snap back against the engine. Return it

gently to prevent damage to the starter. When starting the engine by recoil

starter, set the key switch at the ON position and pull the starter handle.

9.2 Fuel valve lever

The fuel valve is located between the fuel tank and carburetor. When the valve lever is in the

ON position, fuel is allowed to flow from the fuel tank to the carburetor. Be sure to return the

fuel valve lever to the OFF position after stopping the engine.

9.3 Choke rod

The choke is used to provide an enriched fuel mixture when starting a cold engine. It can be

opened and closed by operating the choke rod manually. Pull the rod out toward CLOSED to

enrich the mixture for cold starting.

9.4 Ground terminal

The generator ground terminal is connected to the frame of the generator, the metal non-

current-carrying parts of the generator and the ground terminals of each receptacle

9.5 DC circuit breaker

The DC circuit protector automatically shuts off the DC battery charging circuit when the DC

charging circuit is overloaded, when there is a problem with the battery or when the

connections between the battery and the generator are improper.

9.6 Oil alert system

The oil alert system is designed to prevent engine damage caused by an insufficient amount

of oil in the crankcase. Before the oil level in the crankcase can fall below a safe limit, the oil

alert system will automatically stop the engine (the engine switch will remain in the ON

position). The oil alert system should not take the place of checking the oil level before each

use.

If the engine stops and will not restart, check the engine oil level before troubleshooting in

other areas.

9.7 AC circuit breaker

The AC circuit breaker will automatically switch OFF if there is a short circuit or a significant

overload of the generator at the receptacle. If the AC circuit breaker is switched OFF

automatically, check that the appliance is working properly and does not exceed the rated laod

capacity of the circuit before switching the AC circuit breaker ON again. The AC circuit breaker

may be used to switch the generator power ON or OFF.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX513 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX513

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info