Bedienungsanleitung Powerplus POWXG1013 (Seite 20 von 22) (Englisch)

517139

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

POWXG1013 EN

15 STORING A CHAIN SAW

Caution: never store a chain saw for longer than 30 days without performing the following

procedures. Storing a chain saw for longer than 30 days requires storage maintenance.

Unless the storage instructions are followed, fuel remaining in the carburetor will evaporate,

leaving gum-like deposits. This could lead to difficult starting and result in costly repairs.

 Remove the fuel tank cap slowly to release any pressure in tank. Carefully drain the fuel

tank.

 Start the engine and let it run until the unit stops to remove fuel from carburetor.

 Allow the engine to cool (approx. 5 minutes).

 Using a spark plug wrench, remove the spark plug.

 Pour 1 teaspoon of clean 2-cycle oil into the combustion chamber. Pull starter rope slowly

several times to coat internal components. Replace spark plug. (Fig.19)

Note: store the unit in a dry place and away from possible sources of

ignition such as a furnace, gas hot water heater, gas dryer, etc.

Removing a unit from storage

 Remove spark plug.

 Pull starter rope briskly to clear excess oil from combustion chamber.

 Clean and gap spark plug or install a new spark plug with proper gap.

 Prepare unit for operation.

 Fill fuel tank with proper fuel / oil mixture. See fuel and lubrication section

16 TROUBLE SHOOTING

PROBLEM

PROBABLE CAUSE

CORRECTIVE ACTION

Unit won’t start

or starts but will

not run.

Incorrect starting procedures.

Incorrect carburetor mixture

adjustment setting.

Fouled spark plug.

Empty fuel tank.

Primer bulb was not pressed

enough.

Follow instructions in the user manual.

Have carburetor adjusted by an

authorized service center.

Clean/gap or replace plug.

Fill fuel tank with properly mixed fuel.

Unit starts, but

engine has low

power.

Fuel filter is plugged.

Incorrect lever position.

Dirty spark arrestor screen.

Dirty air filter.

Incorrect carburetor mixture

adjustment setting service

dealer.

Replace the fuel filter.

Move to run position.

Replace spark arrestor screen.

Remove, clean and reinstall filter.

Have carburetor adjusted by an

authorized service center.

Engine

hesitates.

Incorrect carburetor mixture

adjustment setting.

Air filter is plugged.

Old or improperly mixed fuel.

Have carburetor adjusted by an

authorized service center.

Replace or clean the air filter.

Drain gas tank/add fresh fuel mixture.

No power under

load.

Incorrect carburetor mixture

adjustment setting.

Old or improperly mixed fuel.

Air filter is plugged.

Fouled spark plug.

Have carburetor adjusted by an

authorized service center.

Drain gas tank (see storage)/add fresh

fuel mixture.

Replace or clean the air filter.

Replace or clean the spark plug.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWXG1013 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWXG1013

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info