Bedienungsanleitung Powerplus POWXG1018 (Seite 8 von 22) (Englisch)

517143

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

POWXG1018 EN

 Place the slotted end of the guide bar over the bar bolt (F). Slide guide bar behind clutch

drum (G) until the guide bar stops (fig. 3d.

8.3.1 To install saw chain:

Always wear heavy duty gloves when handling saw chain or making saw chain adjustments.

 Spread chain out in a loop with cutting edges (A) pointing clockwise around loop (fig. 4a).

 Slip the chain around the sprocket (B) behind the clutch (C). Make sure the links fit

between the sprocket teeth (fig. 4b).

 Guide the drive links into the groove (D) and around the end of the bar (fig. 4b).

Note: the saw chain may droop slightly on the lower part of bar. This is

normal.

 Pull guide bar forward until chain is snug. Ensure all drive links are in the bar groove.

 Install the clutch cover making sure the tang is positioned in the lower hole in the guide

bar. Make sure the chain does not slip off of the bar. Install the bar retaining nut hand tight

and follow tension adjustment instructions in section saw chain tension adjustment.

Note: the guide bar retaining nuts are installed only hand tight at this point

because saw chain adjustment is required. Follow instructions in section

saw chain tension adjustment.

8.3.2 Saw chain tension adjustment

Proper tension of saw chain is extremely important and must be checked before starting, as

well as during any cutting operation.

Taking the time to make needed adjustments to the saw chain will result in improved cutting

performance and prolonged chain life.

Warning: always wear heavy duty gloves when handling saw chain or

making saw chain adjustments.

8.3.3 To adjust saw chain:

 Hold nose of guide bar up and turn adjustment screw (A) clockwise to increase chain

tension. Turning screw counterclockwise will decrease amount of tension on chain. Ensure

the chain fits snugly all the way around the guide bar. (fig 5)

 After making adjustment, and while still holding nose of bar in the uppermost position,

tighten the bar retaining nuts securely. Chain has proper tension when it has a snug fit all

around and can be pulled around by gloved hand.

Note: if chain is difficult to rotate on guide bar or if it binds, too much

tension has been applied. This requires minor adjustment as follows:

 Loosen the bar retaining nuts so they are finger tight. Decrease tension by turning the bar

adjustment screw counterclockwise slowly. Move chain back and forth on bar. Continue to

adjust until chain rotates freely, but fits snugly. Increase tension by turning bar adjustment

screw clockwise.

 When saw chain has proper tension, hold nose of bar in the uppermost position and

tighten the 2 bar retaining nuts securely.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWXG1018 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWXG1018

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info