Bedienungsanleitung Powerplus POWXG3025 (Seite 13 von 20) (Englisch)

582100

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

POWXG3025 EN

 Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the

centre hole. The most common reason why cracks are formed is that sharp corners have

been formed at the bottom of the teeth while sharpening or that the blade has been used

with dull teeth. Discard a blade if cracks are found.

 Check that the support flange is not cracked due to fatigue or due to being tightened too

much. Discard the support flange if it is cracked.

 Ensure the locking nut has not lost its captive force. The nut lock should have a locking

force of at least 1.5 Nm. The tightening torque of the locking nut should be 35-50 Nm.

 Check that the blade guard is not damaged or cracked. Replace the blade guard if it is

exposed to impact or is cracked.

 Check that the trimmer head and trimmer guard are not damaged or cracked. Replace the

trimmer head or trimmer guard if they have been exposed to impact or are cracked.

11.3.2 Starting and stopping

The complete clutch cover and shaft must be fitted before the machine is started, otherwise

the clutch can come loose and cause personal injury.

Always move the machine away from the refueling area before starting. Place the machine on

a flat surface. Ensure the cutting attachment cannot come into contact with any object.

Make sure no unauthorized persons are in the working area, otherwise there is a risk of

serious personal injury. The safety distance is 15 metres.

11.3.2.1 Cold starting:

A “cold” start of the engine means starting it after at least 5 minutes from when it was switched

off or after refueling.

 Starting: Ignition: Press down the “I” side of the engine switch. (Fig. 21)

 Primer bulb: Press the primer bulb repeatedly until fuel begins to fill the bulb. The bulb

need not be completely filled. (Fig. 22)

 Choke: Set the choke knob in the choke position. (Fig. 23)

 Throttle lock button: When pressing throttle trigger lock-out and throttle trigger, press the

throttle lock button simultaneously, and then release throttle trigger and throttle trigger

lock-out. (Fig. 24)

The throttle lock will automatically release by pressing the throttle trigger

again. If you manually turn the choke knob from choke position to run

position before releasing the throttle lock button, the cutting attachment

will start to rotate immediately when the engine is started.

 Hold the body of the machine on the ground using your left hand (CAUTION! Not with your

foot!). Grip the starter handle, slowly pull out the cord with your right hand until you feel

some resistance (the starter pawls grip), now quickly and powerfully pull the cord. Never

twist the starter cord around your hand. Repeat pulling the cord until engine firing occur.

(Fig. 25)

 Choke: Set the choke knob in the open position. (Fig. 26)

 Repeat pulling the cord until engine start. When the engine starts, allow the engine to

warm up with the throttle lock engaged. Then, pressing throttle trigger to release the

throttle lock. (Fig. 27)

Do not pull the starter cord all the way out and do not let go of the starter handle when the

cord is fully extended. This can damage the machine.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWXG3025 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWXG3025

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info