Bedienungsanleitung Powerplus POWXG9417 (Seite 3 von 7) (Englisch)

582195

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

POWXG9417 EN

5 BEFORE START-UP, NOTE THE FOLLOWING!

 The pump can be connected to any shock-proof plug which has been installed according

to regulations. The plug must have a supply voltage of 230V ~ 5 Hz. Fuse min. 6 Amp.

Caution!

When the pump is to be used near swimming pools or garden ponds and in their area of

protection, it must be equipped with a PRCD (residual current circuit breaker) with a nominal

trip current of max. 30 mA (according to VDE 0100, part 702 and 738).

The pump must not be operated while people are in the swimming pool or in the garden pond!

Please contact your electrician!

Attention!

(Important for your own security) Before starting to run your new submersible pump, please

have the following items checked by an expert:

 Ground connection

 Zero conductor

 Fault current breaker switch must correspond to the safety regulations of the power plants

and they must work faultlessly.

 The electrical connections must be protected from moisture.

 If there is danger of flooding, the electrical connections must be taken to higher ground.

 Circulation of aggressive fluids, as well as the circulation of abrasive materials must be

avoided at all costs.

 The submersible motor-driven pump must be protected from frost.

 The pump must be protected from running dry.

 Access on the part of children should also be prevented with appropriate measures.

Consistency

Your submersible pump is designed for the circulation of water with a maximum temperature

of 35° C. This pump may not be used for other fluids, especially motor fuels, cleaning fluids,

and other chemical products!

6 INSTALLATION

The submersible motor pump is installed as follows:

 In a stationary position with fixed pipeline

 in a stationary position with a flexible hose pipe.

Please note!

You should never install the pump by suspending it unsupported from its delivery pipe or

power cable. The submersible motor pump must be suspended from the specially provided

handle or be placed on the bottom of the shaft. To guarantee that the pump works properly,

the bottom of the shaft must be kept free of sludge and dirt of all kinds.

If the level of water sinks too far, any sludge in the shaft will dry out quickly and stop the pump

from starting up. , Therefore it is necessary to check the submersible motor pump regularly (by

carrying out start-up tests). The “switch on” point can be adjusted by repositioning the sensor

(5) in one of the 4 available positions.

Mains supply

Your new submersible pump is equipped with a shock-proof plug according to regulations. The

pump is designed to be connected to a 230-240V ~50 Hz earthed socket. Make sure that the

socket is sufficiently secured (min. 6 Amp.) and is in excellent condition. Introduce the plug

into the socket and the pump is ready to go.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWXG9417 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWXG9417

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info