Bedienungsanleitung Powerplus POWXG9507 (Seite 3 von 8) (Englisch)

672567

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

POWXG9507 EN

5 GENERAL POWER TOOL SAFETY WARNINGS

Read all safety warnings and all instructions. Failure to follow all warnings and instructions

may result in electric shock, fire and/or serious injury. Save all warnings and instructions for

future reference. The term "power tool" in the warnings refers to your mains operated (corded)

power tool or battery operated (cordless) power tool.

6 BEFORE START-UP, NOTE THE FOLLOWING!

 The pump can be connected to any shock-proof plug which has been installed according

to regulations. The plug must have a supply voltage of 230 V ~ 50 Hz. Fuse min. 6 Amp.

Caution!

When the pump is to be used near swimming pools or garden ponds and in their area of

protection, it must be equipped with a PRCD (residual current circuit breaker) with a nominal

trip current of max. 30 mA (according to VDE 0100, part 702 and 738). The pump must not be

operated while people are in the swimming pool or in the garden pond! Please contact your

electrician!

Attention!

(Important for your own security) Before starting to run your new submersible pump, please

have the following items checked by an expert:

 Ground connection

 Zero conductor

 Fault current breaker switch must correspond the safety regulations of the power plants

and they must work faultlessly.

 The electrical connections must be protected from moisture.

 If there is danger of flooding, the electrical connections must be taken to higher ground.

 Circulation of aggressive fluids, as well as the circulation of abrasive materials must be

avoided at all costs.

 The submersible motor-driven pump must be protected from frost.

 The pump must be protected from running dry.

 Access on the part of children should also be prevented with appropriate measures.

Consistency

Your submersible pump is designed for the circulation of water with a maximum temperature

of 35° C. This pump may not be used for other fluids, especially motor fuels, cleaning fluids,

and other chemical products!

7 INSTALLATION

The submersible pump is installed as follows:

 In a stationary position with fixed pipeline

 in a stationary position with a flexible hose pipe.

Please note!

You should never install the pump by suspending it unsupported from its delivery pipe or

power cable. The submersible pump must be suspended from the specially provided handle or

be placed on the bottom of the shaft. To guarantee that the pump works properly, the bottom

of the shaft must be kept free of sludge and dirt of all kinds.

If the level of water sinks too far, any sludge in the shaft will dry out quickly and stop the pump

from starting up. ,Therefore it is necessary to check the submersible motor pump regularly (by

carrying out start-up tests). The floater is adjusted in a way that the pump can immediately be

started

Note!

The pump shaft should have minimum dimensions of 40 x 40 x 50 cm, so that the floating

switch can move freely.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWXG9507 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWXG9507

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info