Bedienungsanleitung Powerplus POWXQ5320 (Seite 6 von 11) (Englisch)

481023

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

POWXQ5320 EN

5.6 Check damaged parts

§ Before further use of tool, it should be carefully checked to determine that it will operate

properly and perform its intended function.

§ Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting

and any other conditions that may affect its operation.

§ A guard or other part that is damaged should be properly repaired or replaced by an

authorized service centre unless otherwise indicated in this instruction manual.

§ Have defective switches replaced by an authorized service centre.

§ Do not use the tool if the switch does not turn it on and off.

6 ADDITIONAL SAFETY INSTRUCTIONS FOR TILE CUTTERS

§ Make sure that the cutting disc is correctly screened by the guard.

§ Never remove the riving knife. The distance between the cutting disc and the riving knife

should not exceed 5 mm.

§ Do not use cutting discs which are bent, deformed or otherwise damaged.

§ Do not use cutting discs which do not comply with the specifications stated in this manual.

§ Never start cutting tiles before the machine reaches full speed.

§ Never attempt to cut extremely small work pieces. Only cut tiles with a max diameter of

180 mm.

§ Do not leave the work area until the machine has been switched off and the cutting disc

has come to a complete standstill.

§ Never attempt to stop the cutting disc by exerting pressure on the side of the disc.

§ Always unplug the machine before performing any maintenance.

§ Do not use the machine before it has been completely assembled and installed according

to the instructions.

§ Do not perform any design, assembly or Construction activities on the table while the

machine is switched on.

§ Unplug the machine and clean the table before leaving the work area.

6.1 Power supply

§ This tile saw must be connected to an earthed 230V - 50Hz power source.

§ This power source must be secured by a 16A fuse.

§ Your machine is supplied with a 30mA residual current device to protect the user against

electric shock. The device has a test button. Please test this regularly. Preferable before

each work.

§ It can only protect you when the power mains to which the tool is plugged is properly

grounded.

§ Have the proper outlet installed by a qualified electrician.

§ Check with a qualified electrician or service personnel if the grounding instructions are not

completely understood, or if in doubt as to whether the tool is properly grounded.

6.2 Diamond blades

§ Only use 180 mm diameter Continuous Rim Wet Diamond blades.

§ DO NOT use larger, segmented or 'turbo' blades, wood sawing blades, or any other

cutting device. Severe bodily injury, and damage to your saw can occur.

§ Inspect blades daily for cracks or uneven wear. Discard cracked, chipped or bent blades!

§ Ensure the blade is mounted with the rotation arrow in the proper direction and is securely

tightened with a wrench.

§ Always ensure a continuous flow of water on both sides of the blade before cutting any

material.

§ Do not operate the machine without all safety guards in position

§ Do not force the material into the blade. Let the blade cut at its own speed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWXQ5320 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWXQ5320

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info