Bedienungsanleitung Powerplus POWXQG4060 (Seite 8 von 20) (Englisch)

582079

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

POWXQG4060 EN

7.3.4 To adjust saw chain:

 Hold nose of guide bar up and turn adjustment screw (16) clockwise to increase chain

tension. Turning screw counterclockwise will decrease amount of tension on chain. Ensure

the chain fits snugly all the way around the guide bar. (fig 5)

 After making adjustment, and while still holding nose of bar in the uppermost position,

tighten the bar retaining nuts securely. Chain has proper tension when it has a snug fit all

around and can be pulled around by gloved hand.

Note: if chain is difficult to rotate on guide bar or if it binds, too much

tension has been applied. This requires minor adjustment as follows:

 Loosen the bar retaining nuts so they are finger tight. Decrease tension by turning the bar

adjustment screw counterclockwise slowly. Move chain back and forth on bar. Continue to

adjust until chain rotates freely, but fits snugly. Increase tension by turning bar adjustment

screw clockwise.

 When saw chain has proper tension, hold nose of bar in the uppermost position and

tighten the 2 bar retaining nuts securely.

Caution: a new saw chain stretches, requiring adjustment after as few as 5

cuts. This is normal with a new chain, and the interval between future

adjustments will lengthen quickly.

Caution: if saw chain is too loose or too tight, the sprocket, bar, chain, and

crankshaft bearings will wear more rapidly. Study fig.6 for information

concerning correct cold tension (A), correct warm tension (B), and as a

guide for when saw chain needs adjustment (C).

7.3.5 Chain brake mechanical test

Your chain saw is equipped with a chain brake that reduces possibility of injury due to

kickback. The brake is activated if pressure is applied against brake lever when, as in the

event of kickback, operator’s hand strikes the lever. When the brake is actuated, chain

movement stops abruptly.

Warning: the purpose of the chain brake is to reduce the possibility of

injury due to kickback; however, it cannot provide the intended measure of

protection if the saw is operated carelessly. Always test the chain brake

before using your saw and periodically while on the job.

7.3.6 To test chain brake:

 The chain brake is disengaged (chain can move) when brake lever is pulled back and

locked. Be sure the chain brake latch is in the off position. (fig. 7a)

 The chain brake is engaged (chain is stopped) when brake lever is in forward position and

the chain brake latch is in the on position. You should not be able to move chain. (fig. 7b)

Note: the brake lever should snap into both positions. If strong resistance

is felt, or lever does not move into either position, do not use your saw.

Take it immediately to a professional service center for repair.

Don’t let your motor run in high speed when your chainbrake is activated.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWXQG4060 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWXQG4060

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info