Bedienungsanleitung PowerTech PTRV- 17.5K (Seite 37 von 56) (Englisch)

685370

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

GENERATOR ENCLOSURES

Some installations require the Genset to be mounted inside an enclosure. Enclosures are

generally constructed of heavy gauge sheet metal, and completely insulated. Enclosures are

typically installed in RV’s with large unobstructed compartments. The major advantage to

installing a Genset in an enclosure is to achieve a significant reduction in the unit’s sound level.

In order to maintain the ambient temperature within the enclosure a forced cool air

system is generally employed. Two blower fans capable of producing a minimum of 465 CFM

each should be mounted at the generator end of the enclosure. Cooling air circulates around the

generator end and engine, forcing excess heat to exit through an air duct outlet to the outside air.

Since hot air will rise the air duct outlet opening should be located near the inside top surface of

the enclosure, the opening should be approximately 25 square inches.

Openings in the base of the enclosure and compartment floor are required for the engine

exhaust pipe, oil drain hose and engine breather hose. Other holes for fuel lines, electrical leads,

remote radiator hoses, etc. are usually located in the rear wall of the enclosure. Be sure to seal

around these items to prevent fumes or vapors from entering the vehicles compartment. Two

hinged doors at the front of the enclosure enable unobstructed access to the engine and control

box for routine maintenance. A removable service panel in the rear wall of the enclosure

facilitates servicing the back side of the Genset.

The clearance between the enclosure and the vehicles compartment walls is another

consideration. Except for the rear wall of the enclosure the clearances at the top, sides and front

can be minimal. A ½” gap per side is enough clearance for easy installation or removal. At the

rear of the enclosure the compartment depth must be large enough to accommodate the two

blower fans and system connections. A minimum of 10” between the enclosure and rear

compartment wall is required for this area. Also, remember a 400 sq. inch free air opening is

required to supply the forced air cooling system. See section on “Air Requirements” for details.

Dimensions and layouts are provided for your planned installation, be sure to follow all

requirements. Power Technology’s Customer Service Department is available to answer any

questions you may have concerning your Genset and installation.

IMPORTANT: When installing a RV generator set the installation must comply with the

current Safety Standards of ANSI / RVIA EGS-1-2003, ANSI A 119.2 / NFPA 501C and

applicable articles of ANSI / NFPA 70 of the National Electrical Code. Generator set

installations must also comply with state and local requirements.

IMPORTANT: An enclosure manufactured by any person (s) other then Power Technology

must follow the requirements set forth in this manual. All specifications must be adhered to;

failure to do so may affect your Power Technology Southeast, Inc. Limited Warranty.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

PowerTech PTRV- 17.5K Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info