Bedienungsanleitung PowerTech PTRV- 3 RR (Seite 12 von 44) (Englisch)

685358

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

OPERATING THE ENGINE

ENGINE STARTING CONTROLS

1) Generator Main / ECU Reset Switch must be in the ON position.

2) Hold Start/Stop Switch for 1 second and release.

3) Glow Plugs will preheat for 8 seconds. LED flashes slowly.

4) Preheating will cease during engine cranking cycle. LED continues flashing.

5) Engine begins an 8 seconds crank cycle, After 4 seconds of cranking the PT-ECU-63 will check

for an AC signal from the generator. If an AC signal is verified the engine will start and the LED

will remain ON during the normal run operation. If the AC signal is not verified the PT-ECU-63

will terminate the cranking cycle and LED will flash a fault code.

6) Starter disengages immediately after engine run is verified.

7) PT-ECU-63 deactivates the Low Oil Pressure and High Water Temperature Switches for 6

seconds, this will assure oil pressure build-up time. If oil pressure does not build-up the engine will

immediately shut down and go into a fault mode. Likewise for a high temperature situation.

8) If engine will not start on the first attempt the PT-ECU-63 will initiate the start cycle 2 more times

before going into a fault mode. Glow Plugs will preheat for 8 seconds per attempt. Engine will

crank for 8 seconds per attempt.

9) To shut down the engine under normal operations, hold the Start/Stop Switch for 1 second and

release.

10) If a fault occurs turn Generator Main / ECU Reset Switch OFF and then ON to reset PT-ECU-63.

The Main /ECU Reset Switch is located on the generator end, inside the service access door.

NOTE: A RED

indicator light on the control panel will illuminate during the start cycle and then turn off

once oil pressure builds up. If oil pressure drops off during normal operations the RED light will come on

as a “WARNING” only. The operator must shut down the unit immediately and investigate the problem.

This feature is separate from the Low Oil Pressure Switch connected to the PT-ECU-63.

CHECKING ENGINE AFTER STARTING

1) Allow the engine to warm up 3 to 5 minutes before applying a load. In colder climates allow a few

extra minutes longer.

2) Perform a visual inspection of all areas of the engine and generator.

3) Listen for any abnormal noises.

4) Check for any abnormal exhaust gases.

STOPPING THE ENGINE

It is recommended to disconnect or reduce the power load from the generator before shutting down the

engine. Then follow the steps outlined above for normal shut down.

NOTE: The PT-ECU-63 is designed to operate on 12V DC power. In a low battery situation the

PT-ECU-63 may not initiate the normal cranking cycle. To start the generator you can press and

hold the Start/Stop Switch for approximately 10 seconds or until the engine starts. Once the

engine starts the PT-ECU-63 will resume normal operations. If this situation re-occurs, charge or

replace the battery.

IMPORTANT: Damage to the Starter Motor, Starter Solenoid, Run Solenoid or any generator component

due to excessive or prolonged starting attempts attributed to an external Low Battery Control Monitoring

or Auto-Start System will not be covered by the Power Technology Southeast, Inc. Limited Warranty.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

PowerTech PTRV- 3 RR Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info