Bedienungsanleitung PowerTech PTRV-17.5KT (Seite 33 von 56) (Englisch)

685372

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

GENERATOR INSTALLATION

In RECREATIONAL VEHICLES

INTRODUCTION

Use this section as a guide when installing a generator set in a recreational vehicle, and then refer

to the appropriate operation section for specific instructions. When installing a RV generator set the

installation must comply with the current Safety Standards of ANSI / RVIA EGS-1-2003, ANSI A 119.2

/ NFPA 501C and applicable articles of ANSI / NFPA 70 of the National Electrical Code. Generator set

installations must also comply with state and local requirements.

MARINE APPLICATION

RV generator sets do not comply with United States Coast Guard (USCG) requirements and

must not be used for marine applications. Use only generator sets specified for marine use in marine

installations. USCG regulation 33CFR183 requires a generator set to be “ignition protected” when used

in a gasoline fueled environment.

GENERAL INFORMATION

This information section covers the RV generator set models listed below. To determine which

model is involved, check the model number found on the Power Technology nameplate attached to the

frame of the generator being installed. Follow all instructions to ensure proper installation and operation.

Each generator set features a Kubota diesel engine, rotating-field alternating current generator,

and a control box. The generator is directly connected to the engine for permanent alignment. Each

control box includes a Start / Stop switch, and a On /Off switch to reset the control module or lockout

any remote switch to prevent starting while service is being performed. The control box may also be

equipped with a switch to operate the mechanism used to move the generator in/out of the coach for

servicing. (Supplied by the coach manufacture). After the set is attached to the frame of the vehicle, all

that is usually required to make it operational is the following.

1. Attaching the exhaust system.

2. Add proper amount of radiator coolant.

3. Add oil to crankcase, to the dipstick FULL mark.

4. Connect fuel lines, remote switch, load leads and battery terminals.

(Consult the Specification Charts on the Following Pages for Requirements)

MODELS PTRV-17.5K PTRV-20K PTRV-17.5KT PTRV-20KT

DIMENSIONS L x W x H 41” x 27” x 28” 42” x 27” x 28” 41” x 27” x 28” 42” x 27” x 28”

WEIGHT 840 lbs. 850 lbs. 840 lbs. 850lbs.

ENGINE Kubota V-2203 Kubota V-2003-T Kubota V-2203 Kubota V-2003-T

RPMs 1800 1800 1800 1800

KW RATING 17.5 20 17.5 20

AC VOLTAGE 120 / 240 120 / 240 120/240 120/240

AMPERAGE 146/73 166/83 146/73 166/83

Hz 60 60 60 60

PHASE 1 1 1 1

GENERATOR COMPARTMENT

FREE AIR OPENING

400

Square Inches

400

Square Inches

400

Square Inches

400

Square Inches

RADIATOR AIR REQUIREMENTS 2120 CFM 2120 CFM 2120 CFM 2120 CFM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

PowerTech PTRV-17.5KT Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info