Bedienungsanleitung PowerTech PTS-20 (Seite 22 von 66) (Englisch)

685354

Zoom out

Zoom in

Vorherige Seite

1/66

Nächste Seite

GENERATOR ASSEMBLY INFORMATION

EXCITER TYPE GENERATOR

The exciter pole pieces contain residual magnetism, which sets up lines of force across the air

gap to the exciter armature. When the exciter begins to rotate a voltage is induced and current flow is

initiated in the exciter armature AC windings. This voltage is fed to the rotating rectifier assembly,

rectified and fed to the alternator field, which sets up lines of force across the air gap to the alternator

stator windings and to the output circuit.

A static voltage regulator is connected to the generator output. The regulator will rectify part of

the output voltage to provide a DC voltage to the exciter field coils. This will increase the density of the

lines of force in the exciter, increasing the voltage induced into the exciter armature windings, and

therefore, to the rotating rectifiers. The rotating rectifier output will be increased which will increase the

alternator field strength and generator output will build up its rated voltage. Adjustment of the generator

output to the rated voltage level is accomplished by controlling the current fed to the exciter field coils.

Regulation is automatic with the static type voltage regulator. An additional voltage adjustment range is

provided if desired by turning the Voltage Adjust Rheostat.

ELECTRONIC VOLTAGE REGULATION

Electronic Voltage Regulator (EVR) also referred to, as an Automatic Voltage Regulator (AVR)

is a very reliable device, which uses solid-state electronics to maintain voltage accuracy at ±2% of the

regulated voltage. The Voltage Regulator is designed to automatically regulate and maintain the

generated AC voltage through out the load range that is from no load to full load.

VOLTAGE CONNECTION

The generator may be connected at the terminal board to deliver 120/240 volts to a 3 wire

grounded neutral system, or 120-volts only to a 2 wire distribution system. If any equipment requires

240-volts, then the 120/240-volt connection must be used. If all equipment requires 120-volts then

the 120-volt connection is preferred, even if two lines leave the same switch box. The two lines at

the inputs to the switch box are both connected to the un-grounded 120-volt lines from the generator.

The 120-volt connection enables the Electronic Voltage Regulator (EVR) to hold the voltage very

close to the 115 or 120 volts, as initially adjusted, regardless of the power distribution amount the

different distribution lines. The 120-volt connection is recommended if the entire electrical load

requires only 115 or 120 volts.

Although the 120/240-volt connection may also be used when all loads requires only 110 volts, it

should be pointed out that this connection, the 240-volts, is regulated and the lightly loaded phase, or

line, will deliver a high line to neutral voltage and the heavily loaded phase will deliver a low line to

neutral voltage. The heavily loaded line may have such a low voltage that air conditioning will have

more difficulty in starting, and long starting lines may overload generator and trip circuit breakers

EXCITER FIELD COIL VOLTAGE SOURCE

Field coil DC voltage is obtained by rectifying the voltage from the phase to neutral line of the

generator output, or either appropriate terminal to provide the needed voltage reference.

The rectifier bridge is an internal part of the static regulator. The static regulator senses a change

in the generator output and automatically regulates current flow in the exciter field coil circuit to

increase or decrease the exciter field strength. An adjustable rheostat sized to be compatible with

the regulator is used to provide adjustment of the regulator sensing circuit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

PowerTech PTS-20 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info