Bedienungsanleitung Precor S3.19 Leg Press Option (Seite 5 von 16) (Englisch)

604335

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

S3.15/S3.19 Leg Press Option Assembly Instructions

page 5

Preparations

You must review and follow the instructions in this

guide. If you do not assemble and use the Leg Press

Option according to the following guidelines, you could

void the Precor Limited Warranty.

Required Tools

Tools that you need to obtain before assembling the

unit include:

❏ ⁹⁄₁₆-inch socket

❏ ³⁄₄-inch socket

❏ ⁹⁄₁₆-inch box-end wrench

❏ ³⁄₄-inch box-end wrench

❏ Crescent wrench

❏ Wire tie cutter (cuts plastic tie wraps)

❏ Utility knife

Installation Requirements

Follow these installation requirements when

assembling the unit:

• Fill out and mail the warranty registration card.

• Set up the Leg Press Option on a solid, flat

surface. A smooth, flat surface under the unit

helps keep it level.

• Provide ample space around the machine.

Open space around the machine allows for easier

access.

• Insert all fasteners in the same direction. For

aesthetic purposes, insert all the fasteners in the

same direction unless specified (in text or

illustrations) to do otherwise.

• Leave room for adjustments. Tighten fasteners

(such as screws, nuts, and bolts), so the unit is

stable, but leaves room for adjustments. Do not

fully tighten fasteners until instructed (in the steps)

to do so.

Assembly Tips

• Fasteners may become loose and fall off during

shipment. Inspect the plastic wrap and packaging

for loose parts. To alleviate confusion during

assembly, reattach the loose fasteners and pulleys

found in the packaging.

• A black 6-inch scale with white numbers is

provided at the bottom of every assembly

instruction page. Use this scale to identify the

correct fastener size. The head of a fastener is not

used in measuring the length.

• Most fasteners are ³⁄₈-inch unless otherwise noted.

To find out the length of a particular fastener,

measure its shank (the long, narrow part beneath

the head). Refer to the following diagram:

• Zinc fasteners are used with the titanium parts.

Black fasteners are used when assembling the

stone gray painted surfaces.

• Most fasteners are fitted to the frame or pulley, you

will need to disassemble the fasteners before

proceeding with each step. Some pieces have

extra holes that you will not use. Use only those

holes indicated in the instructions and illustrations.

• Read all caution notes on each page before

completing that step.

• While you may be able to assemble the Leg Press

Option by reading the illustrations only, refer to the

text for important safety cautions and notes. The

S3.15 is shown throughtout the assembly

instructions. If you purchased the S31.9, the Leg

Press Option assembly is identical.

Fastener head

Fastener threads

Shank

To determine the

length of a fastener,

measure its shank.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Precor S3.19 Leg Press Option Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info