Bedienungsanleitung President Jackson II Classic (Seite 31 von 52) (Englisch, Französisch, Spanisch, Polnisch)

636606

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

7) DISPLAY

The digital LED display shows the channel, its con-

ﬁguration and the level of some adjustments.

8) ASC/VOX LED

This led is green when the ASC function is active and red when the VOX

function is active. It’s orange when both functions are active.

9) RX/TX LED

This led is red in transmission and green when a signal is received.

10) DIM

The DIMMER function allows adjusting the brightness of the lighting.

11) F - FREQUENCY BAND SELECTION

(conﬁguration: EU; PL; d; EC; U; In)

The frequency bands have to be chosen according with the country of use.

Don’t use another conﬁguration. Some countries need a user’s licence.

See table page 51.

Proceeding: - switch off the transceiver. Put the switch (11) on «F» position

and switch on again. The letter corresponds to the blinking conﬁguration.

- In order to change the conﬁguration, use the channel selector on the front

panel or the UP/DN keys (6) of the microphone.

- When the conﬁguration is selected, put the switch (11) on «OFF». The letter

that corresponds to the conﬁguration are continuously displayed. At this point,

conﬁrm the selection by switching off the transceiver and then switching it

on again.

See the conﬁgurations / frequency bands table at pages 46 to 50.

12) PRIORITY CHANNEL

This switch selects channel 9 or 19 according to the conﬁguration.

See table page 50.

13) ROGER BEEP

The Roger beep sounds while releasing the microphone key in order to let your

correspondent speak. Historically, CB is a mode of «simplex» communication.

This means that it is not possible to speak and to listen at the same time (as

it is the case with a telephone). Once someone had ﬁnished to talk, he said

“Roger” in order to prevent his correspondent that it was his turn to talk.

“Roger” has been replaced by a beep. There comes «Roger beep» from.

Note: the «Roger Beep» also sounds in the loudspeaker if the function is al-

ready active while switching on the transceiver. If the function is on OFF while

switching on the radio, only the correspondent can hear the «Roger Beep».

14) NB.ANL / HI-CUT

3 positions switch: Off / NB.ANL ﬁlter activated / NB.ANL + HI-CUT activated.

NB.ANL: Noise Blanker / Automatic Noise Limiter. These ﬁlters allow reducing

back ground noises and some reception interferences. In FM and USB/LSB

mode, only the NB ﬁlter is active.

HI-CUT: Cuts out the high frequency interferences and has to be used in

accordance with the reception conditions.

15) S/RF ~ SWR ~ CAL

3 positions switch: changing meter function.

S/RF

Analogue S/RF meter which shows the power in transmission and reception.

SWR

Shows the value of the SWR (see proceedings of the SWR adjustment at page

29).

CAL

Calibration of the SWR meter (see proceedings of the SWR meter at page

29).

16) METER

Shows the level of the signal in transmission and reception, the SWR or the

calibration of the SWR according to the position of the S/RF~SWR~CAL (15)

switch.

17) 6-PIN MICROPHONE PLUG

This plug is situated on the front panel of the radio making the setting of the

equipment into the dashboard easier.

See the cabling diagram at page 49.

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

President Jackson II Classic Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info