Bedienungsanleitung President Johnson II (Seite 33 von 52) (Englisch, Spanisch)

636619

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

a) press MEM during the scanning cycle of the channels. «MEM» is displayed.

The transceiver scans the active memories (M1, M2, M3) and channels 19

and 9.

b) press SCAN during the recall cycle MEM of the memories. «SCAN» is displayed.

The transceiver scans the active memories (M1, M2, M3) and channels 19

and 9.

M2 (see § 9)

8) AM/FM ~ LOCAL ~ M1

AM/FM

(short push)

This switch allows to select the modulation mode AM or FM.

Your modulation mode must correspond with the one of the person you are

speaking to.

AM/ Amplitude Modulation (AM) is for communications in areas where there

are obstacles and over medium distances.

FM/ Frequency Modulation (FM) is for nearby communications in ﬂat, open

areas.

AM/FM 2

function (only in U conﬁguration)

Allows to alternate the frequency bands CEPT and ENG in the U conﬁgura-

tion. When the ENG frequency band is selected, «UK» is displayed.

LOCAL (long push)

Allows the automatic adjustment of the RF Gain for close communication.

«LOCAL» is displayed.

M1 (see § 9)

9) MEM ~ F

MEM

3 channels can be memorized with following parameters: AM (except for

EC and U conﬁgurations) or FM; LOCAL; NB/ANL; HICUT (and CEPT/ENG in

the U conﬁguration)

To memorize:

- press shortly on MEM, «MEM» blinks.

- Press during 1 s on M1, M2 or M3. «MEM» is displayed continuously. The

channel has been memorized.

To recall a memory:

- press shortly on MEM, «MEM» blinks.

- press shortly on M1, M2 or M3.

- «MEM» is displayed continuously. The memorized channel is active.

To delete a memory:

- turn off the transceiver.

- keep key M1, M2 or M3 pressed and switch on the transceiver.

- the selected memory is deleted.

F - FREQUENCY BAND SELECTION

(conﬁguration: E; d; EU; EC; U; PL)

The frequency bands must be chosen according to the country where you

are going to operate. Do not use another conﬁguration. Some countries

require user’s licence.

See the table on page 51.

How to proceed:

- switch off the transceiver

- press and hold the F key and switch on the transceiver. «F» blinks and the

letter corresponding to the conﬁguration blinks.

- In order to change the conﬁguration, use the / keys on the front panel

or UP and DN on the microphone.

- When the conﬁguration is selected, press on the F key during 1 s. «F» and

the letter corresponding to the conﬁguration is continuously displayed. At

this stage, conﬁrm the selection by switching off then switching on again the

transceiver.

See tables on page 47 ~ 5t0.

10) 6-PIN MICROPHONE PLUG

This plug is situated on the front panel, thereby making it easier to set the

equipment into the dashboard. See the cabling diagram on page 49.

11) PTT (push to talk)

Press this knob to transmit a message and release to listen to an incoming

communication.

A) DC-POWER TERMINAL (13.2 V)

B) ANTENNA CONNECTOR (SO-239)

C) EXTERNAL SPEAKER JACK (8 Ω, Ø 3.5 mm)

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

President Johnson II Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von President Johnson II

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info