Bedienungsanleitung President MC 8000 DSC (Seite 36 von 48) (Englisch)

636661

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Problem

I can’t hear anything (no

volume) from the speaker.

I can transmit, but no one

can hear me.

Thedisplayashes,andI

don’t know why.

I can’t read the display.

The display is too bright

at night.

I can’t see any words on

the display.

I’m not getting any GPS

data on my display.

I’m not getting any hazard

alerts.

I’m getting all the hazard

alerts, not just the ones for

my area.

Ican’tmakeGroupDSC

calls.

WherecanIndmy

radio’sserialnumber?

The radio won’t let me

enter my User MMSI.

WhatdoIdo?

Things to Try

Adjust the squelch level; it is probably too high.

Check your UIC channel settings (see Setting the UIC channel mode

(USA/CAN/INT) on page 8).

Thedisplaywillashiftheradioisinawatchmodeorinscanmode.

Tryturningoffscanning,WeatherAlertWatch,orTriple/DualWatch

(see page 16.)

Adjust the contrast and backlight brightness level (see page 18)

Adjust the backlight brightness level.

Turn off the radio; hold CALL-MENU button and turn it back on (see

page 18)

Reset the radio back to the default brightness level: turn off the radio;

hold the CALL-MENU button and turn it back on.

Make sure your GPS receiver is correctly connected (see Connecting

to a GPS receiver, page 32).

Make sure your GPS receiver is working properly. Make sure that your

GPS receiver supports the NMEA parameters described in NMEA

Operation on page 45.

Make sure Weather Alert Watch is turned on.

Check to make sure the FIPS codes in your radio include your current

location (see Using FIPS codes for weather alerts on page 17).

Check to make sure the FIPS codes in your radio were entered cor-

rectly (see Using FIPS codes for weather alerts on page 17). Some-

times the Weather Alert Watch may catch a hazard alert in the middle

of the broadcast and miss which FIPS codes are affected. For your

safety, the radio triggers the alert tone and switches to the weather

channel when this happens.

Make sure the Group MMSI was entered correctly.

Look on the right side of the radio (the side with the microphone cord),

behind the mounting bracket.

Contact customer service.

Engine Noise Suppression

Interference from the noise generated by the electrical systems of engines is sometimes a

problem with radios. Your radio has been designed to be essentially impervious to ignition

noise and alternator noise. However, in some installations it may be necessary to take meas-

urestofurtherreducetheeffectofnoiseinterference.Yourradio’sDCbatterywires,antenna

lead, and accessory cables should be routed away from the engine and engine compart-

ment, and from power cabling carrying high currents. In severe cases of noise interference, it

may be necessary to install a noise suppression kit. Contact the dealer where you purchased

the radio for more information.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

President MC 8000 DSC Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von President MC 8000 DSC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info